Vertical System |
| Analog Bandwidth @ 50 Ω (-3 dB) | 6 GHz |
| Rise Time (typical) | 75 ps |
| Input Channels | 4 |
| Bandwidth Limiters | 20 MHz, 200 MHz, 1 GHz, 3 GHz, 4 GHz |
| Input Impedance | 50 Ω ±2.0% |
| Input Coupling | DC, GND |
| Maximum Input Voltage | ±4 Vpeak |
| Channel-Channel Isolation | = 100:1 at 2 GHz; = 40:1 at 3 GHz; = 20:1 at 4 GHz |
| Vertical Resolution | 8 bits; up to 11 bits with enhanced resolution (ERES) |
| Sensitivity | 2 mV–1 V/div (fully variable, < 10 mV/div through zoom) |
| DC Gain Accuracy | ±1.5% of full scale |
| Offset Range | ±750 mV @ 2 mV–194 mV/div ±4 V @ 196 mV–1 V/div |
| Offset Accuracy | ±(1.5% of full scale +1.5% of offset value +2 mV) |
| |
Horizontal System |
| Timebases | Internal timebase common to 4 input channels; an external clock may be applied at the auxiliary input |
| Time/Division Range | Real Time: 20 ps/div – 10 s/div
Random Interleave Sampling: to 20 ps/div, Upper time/div limit function of sample rate and memory length settings |
| Time Interval Accuracy | = 0.06 / SR + (1 ppm, aging < 1 ppm/year * Reading) (rms) |
| Jitter Noise Floor | 1 ps rms (typical) |
| Trigger Jitter | <= 2 ps rms (typical) |
| Sample Rate and Delay Time Accuracy | ±1 ppm, aging < 1 ppm/year = 10 sec interval |
| Channel-Channel Deskew Range | ±9 x time/div. setting, or 25 ns, whichever is larger |
| External Timebase Reference | 100 MHz; 50 Ω impedance, applied at the rear input |
| External Clock Frequency | 30 MHz–2 GHz, 50 Ω impedance, applied at the auxiliary input |
| |
Acquisition System |
| Single-Shot Sample Rate/Ch | 20 GS/s on 2 Ch; 10 GS/s on 4 Ch |
| Random Interleaved Sampling (RIS) | 200 GS/s for repetitive signals, to 20 ps /div. Upper time/div limit function of sample rate and memory length settings |
| Maximum Trigger Rate | 150,000 waveforms/second |
| Intersegment Time | 6 µs |
| Maximum Acquisition Memory Points/Ch | (2 Ch) / (4 Ch) |
| Standard Memory (4 Ch / 2 Ch) (Number of Segments) | 96 M / 48 M |
| VL – Memory Option | N/A |
| XL – Memory Option | N/A |
| |
Acquisition Modes |
| Averaging | Summed averaging to 1 million sweeps; continuous averaging to 1 million sweeps |
| Enhanced Resolution (ERES) | From 8.5 to 11 bits vertical resolution |
| Envelope (Extrema) | Envelope, floor, or roof for up to 1 million sweeps |
| |
Triggering System |
| Modes | Normal, Auto, Single, and Stop |
| Coupling Mode | DC |
| Pre-trigger Delay | 0–100% of memory size (adjustable in 1% increments) |
| Post-trigger Delay | the smaller of 0–10,000 divisions or 86400 seconds |
| Hold-off by Time | From 2 ns up to 20 s or from 1 to 99,999,999 events |
| Internal Trigger Range | ±5 div from center |
| Trigger Sensitivity with Edge Trigger (Ch 1–4) | 3 div @ = 5 GHz,
2 div @ < 4 GHz,
1.2 div @ < 3 GHz (typical) |
| External Trigger Sensitivity, (Edge Trigger) | 300 mV @ = 5 GHz,
200 mV < 4 GHz,
120 mV < 3 GHz (typical) |
| External Trigger Input Range | Aux (±0.4 V); Aux X10 (±0.04 V); Aux/10 (±4 V) |
| Max. Trigger Frequency, SMART Trigger | 750 MHz @ = 10 mV |
| |
Basic Triggers |
| Edge | Triggers when signal meets slope and level condition. |
| |
SMART Triggers |
| State or Edge Qualified | Triggers on any input source only if a defined state or edge occurred on another input source.
Delay between sources is selectable by time or events. |
| Dropout | Triggers if signal drops out for longer than selected time between 2 ns and 20 s. |
| Pattern | Logic combination (AND, NAND, OR, NOR) of 5 inputs.
Each source can be high, low, or don’t care. The High and Low level can be selected independently.
Triggers at start or end of the pattern. |
| |
SMART Triggers with Exclusion Technology |
| Glitch | Triggers on positive or negative glitches with widths selectable from 600 ps to 20 s, or on intermittent faults. |
| Signal or Pattern Width | Triggers on positive or negative pulse widths selectable from 600 ps to 20 s, or on intermittent faults. |
| Signal or Pattern Interval | Triggers on intervals selectable between 2 ns and 20 s. |
| |
Color Waveform Display |
| Type | Color 10.4" flat panel TFT-LCD with high resolution touch screen |
| Resolution | SVGA; 800 x 600 pixels |
| Number of traces | Display a maximum of 8 traces. Simultaneously display channel, zoom, memory and math traces. |
| Grid Styles | Auto, Single, Dual, Quad, Octal, X-Y, Single+X-Y, Dual+X-Y |
| Waveform Representation | Sample dots joined, or sample dots only |
| |
Internal Waveform Memory |
| Internal Waveform Memory | 4 active waveform memory traces (M1-M4) store 16 bit/point full length waveforms. Waveforms can be stored to any number of files limited only by the data storage media capacity. |
| |
Automatic Setup |
| Auto Setup | Automatically sets timebase, trigger, and sensitivity to display a wide range of repetitive signals |
| Find Vertical Scale | Automatically sets the vertical sensitivity and offset for the selected channel to display a waveform with the
maximum dynamic range |
| |
Analog Persistence Display |
| Analog and Color-Graded Persistence | Variable saturation levels; stores each trace’s persistence data in memory |
| Trace Selection | Select persistence on all or any combination of traces |
| Sweep Display Modes | All accumulated, or all accumulated with last trace highlighted |
| Persistence Types | Select analog, color graded, or three-dimensional |
| Persistence Aging | Timing Select from 500 ms to infinity |
| |
Processor/CPU |
| Type | Intel® Pentium® 4, 2.54 GHz or better |
| Processor Memory | Up to 2 GB |
| Operating System | Microsoft Windows® XP Professional |
| Oscilloscope Operating Software | Entire instrument including any installed optional applications packages operates within a single Windows application |
| Real Time Clock | Date and time displayed with waveform an in hardcopy files. SNTP support to synchronize to precision internal clocks. |
| |
Setup Storage |
| Setup Storage | Front Panel and Instrument Status Store to the internal hard drive or to a USB-connected peripheral device. |
| |
Interface |
| Remote Control | Via Windows Automation, or via LeCroy Remote Command Set |
| GPIB | Supports IEEE – 488.2 |
| Ethernet (LAN) | Supports 10/100BaseT Ethernet interface |
| USB (Host) | USB 2.0 ports on front and rear panels support Windows® XP compatible devices |
| External Monitor Port | 15 pin D-Type SVGA compatible, duplicates instrument display.
Optional dual monitor support for split Windows® applications |
| Parallel Port | 1 standard |
| |
Auxiliary Input |
| Signal Types | Select External Trigger or External Clock Input on the front panel |
| |
Auxiliary Output |
| Signal Types | Select Calibrator, Trigger Enabled, Trigger Out, Pass/Fail, or Off |
| Calibrator Signal | 5 Hz–5 MHz square wave or DC Level, 0–500 mV into 50 Ω, 0–1.0 V into 1 MΩ, or TTL logic voltages |
| |
General |
| Auto Calibration | Ensures specified DC and timing accuracy is maintained for 1 year minimum. |
| |
Power Requirements |
| Voltage | 100–240 VAC ±10% at 50/60/400 Hz; 200–240 VAC ±10% at 50/60 Hz; Automatic AC Voltage Selection |
| Max. Power Consumption | 650 W/650 VA |
| |
Environmental and Safety |
| Temperature (Operating) | +5 °C to +40 °C including CD-ROM drives |
| Temperature (Non-Operating) | –20 °C to +60 °C |
| Humidity (Operating) | 5% to 80% relative humidity (non-condensing) up to +30 °C. Upper limit derates to 25% relative humidity (non-condensing) at +40 °C. |
| Humidity (Non-Operating) | 5% to 95% relative humidity (non-condensing) as tested per MIL-PRF-28800F |
| Altitude (Operating) | Up to 10,000 ft. (3048 m) at or below +25 °C |
| Altitude (Non-Operating) | Up to 40,000 ft. (12,192 m) |
| |
Physical Dimensions |
| Dimensions (HWD) | (HWD) 264 mm x 397 mm x 491 mm; 10.4" x 15.6" x 19.3" (height excludes feet) |
| Weight | 23 kg; 50 lbs. 18 kg; 39 lbs. 23 kg; 50 lbs. 18 kg; 39 lbs. |
| Shipping Weight | 29 kg; 63 lbs. 24 kg; 53 lbs. 29 kg; 63 lbs. 24 kg; 53 lbs. |
| |
Certifications |
| Certifications | CE Compliant; UL and cUL listed; Conforms to EN 61326 (for EMC); EN 61010, UL 61010B-1
and CSA C22.2 No. 1010.1 (for safety) |
| |
Warranty and Service |
| Warranty and Service | 3-year warranty; calibration recommended annually.
Optional service programs include extended warranty, upgrades, and calibration services. |
| |
