Oscilloscopes
Protocol Analyzers
Differential Amplifiers
Probes
Automotive/Vehicle Test
Mixed Signal Test Solutions
Modular Instruments
Scope Accessories
Hardware Options
Software Options
Discontinued Products
|
|
Mixed Signal Test Solutions
MS-32 Oscilloscope Mixed Signal Option — Add 32 Digital Channels to a 4 Channel Oscilloscope
|
|
|
Finally, the ultimate solution for mixed signal oscilloscopes — enough channels. LeCroy's MS-32 and a WaveSurfer® or WaveRunner® oscilloscope provide 4 analog and 32 digital channels for powerful measurement capability.
|
 |
Leading
Features
- 32 digital channels
- Long capture time
(1 Mpts/Ch of digital memory, always available)
- Ability to capture up to
125 MHz digital clocks
- Simple oscilloscope setup and
user interface
|
|
4 Analog + 32 Digital Channel Capability
LeCroy introduces the first oscilloscope solution to combine 4 analog channels with 32 digital channels. This is ideal for the most efficient testing of 16-bit embedded controllers, where all 16 ADDR and 16 DATA lines can be viewed at one time. Or, a multitude of ADDR and DATA lines can be viewed, in addition to control lines and low-speed serial data lines (SPI, I2C, etc.). Testing and debugging efficiency is greatly enhanced by eliminating the need to continuously disconnect/reconnect signals to observe different behaviors.
|
|
Enhanced Test and Analysis Capabilities for Mixed Signal Environments
LeCroy now offers the perfect solution for embedded controller testing where there are multiple analog signals coincident with digital signals. Analog signals include comparators, voltage sources, sensor/actuator signals, etc.; while digital signals include address or data lines, control signals, or peripheral serial data signals.
Users can capture all their signal information using long memory, or set up digital or analog trigger conditions to capture the event of interest. Signal debug is simple, using standard oscilloscope tools, such as cursors, measurement parameters, and zooming.
|
|
|
| |
Mix
Signal Testing Features |
|
|
Long
Digital Capture Time
|
|
1 Mpts of digital memory/channel ensures that users can capture
their area of interest. 1 Mpts is always available on every channel. |
|
|
Parallel
Bus Definition
|
|
The
digital information obtained by viewing parallel ADDR or DATA bus
information can be defined as a bus display. Users can also define a
digital trigger for a particular bus value. Up to 4 different buses
can be defined. |
|
|
User
Interface
|
|
A
familiar interface eliminates the need to spend a lot of time
learning a new tool. |
|
|
Resize/Reposition
|
|
Digital
lines can be resized and repositioned anywhere on the oscilloscope
grid by using the front panel controls or software menus. |
|
|
Flexibly
Trigger
|
|
Select
from a number of different analog triggers; or create a digital
trigger by defining a digital trigger pattern, logic bus value, or
interval. |
|
|
Cursors
|
|
Cursors
will read time or bus information, as appropriate. |
|
|
Quick
Setup
|
|
Unlike
a traditional Logic Analyzer, the MS-32 is easy to use. A single
module consolidates all of the MS-32/oscilloscope interconnections,
so users can start viewing signals and debugging quickly. In
addition, all standard oscilloscope tools are readily accessible. |
| |
|
Use the MS-32 with Most 4 Channel WaveRunner or WaveSurfer
Oscilloscopes
|
WaveRunner
Xi and 6000A Series
Its
higher performance capabilities and longer standard and optional
memories are intended for customers who need to perform analysis
on long records, or have specific application problems (such as
CAN Bus testing).
|
WaveSurfer
Xs Series and 400 Series
(350 to 600 MHz only)
Designed
for those customers requiring a basic oscilloscope for signal
viewing and for performing basic timing measurements.
|
| Available
for:* |
WR6030A, WR6050A
WR6100A, WR6200A
WR44Xi, WR64Xi |
WS434, WS454
WS44Xs, WS64Xs |
Bandwidth
Range
|
350
MHz – 2 GHz
|
350 MHz – 600 MHz
|
# Analog Channels
|
4 |
4 |
Analog Sample Rate
|
Up to 5 GS/s per Channel
10 GS/s max. (64Xi, 6100A, 6200A)
|
2.5 GS/s per channel
(1 GS/s for 434, 454) |
Analog Memory
|
5
Mpts/Ch standard
Options up to 12 Mpts/Ch |
2.5 Mpts/Ch
(1 Mpts for 434, 454)
|
Digital Memory
|
1
Mpts/Ch (with MS-32)
|
1
Mpts/Ch (with MS-32) |
Application Packages
|
CAN Bus Trigger and Decode
Power Measure and Analysis
Jitter & Timing
Digital Filter
Serial Data Mask
Ethernet (6200A Only)
USB 2.0 (6200A Only)
|
None
|
Display Size
|
8.4" (WR 6000A Series)
10.4" (WRXi Series) |
10.4"
|
|
Operating System |
Windows®
XP |
Windows®
XPe
|
| *MS-32 is also compatible with LeCroy?fs WavePro and WaveMaster Series oscilloscopes, with bandwidths between 1–6 GHz for faster sampling rates and long memory capture. |
|
|
|
|
|
|
|
|
MS-32 System Components
- Oscilloscope Interface Module
- Power Supply
- USB 2.0 Cable
- 32 Channel Digital Logic Pod
- 10.5" Digital Lead Set
- Foam Lined Soft Accessory Case
- 5x Magnifying Glass
(not pictured)
|
|
|
|
|
|
MS-32 Gripper Probe Set Accessories
PK400-1
- Large
gripper probe set for 0.10" (2.54 mm) pin pitch, includes
10 probes with color-coded leads.
|
|
|
|
PK400-2
- Medium
gripper probe set for 0.04" (1.0 mm) pin pitch, includes
10 probes with color-coded leads. |
|
|
|
PK400-3
- Large
gripper probe set for 0.008" (0.2 mm) pin pitch, includes
10 probes with color-coded leads. |
|
|
Specifications
| Digital Channels |
|
Number
|
32 |
Memory
|
1 Mpts/Ch |
Probe Inputs
|
240 kΩ // 10 pF |
Threshold Levels
|
TTL, ECL, CMOS (2.5, 3.3, 5 V), PECL, or User Defined. |
| Sampling Rate |
1 kS/s to 500 MS/s |
| Minimum Input Voltage Range |
±300 mV around the threshold voltage setting |
| Maximum Clock Speed |
125 MHz |
| Maximum Input Voltage |
30
V |
Digital Channel Grouping
|
4 digital groups can be defined. Each group may use any combination of 32 digital lines.Groups can be displayed as individual lines, or collapsed into a bus view. |
Triggering
|
User selectable analog (i.e., std. oscilloscope trigger) or digital trigger
|
| |
|
| Digital Trigger |
|
Setup Type
|
Logic, Logic Bus, or Interval |
Logic
|
Setup Up to 32 digital lines, with any combination of 0, 1, or X (don't care). In addition, a Rising Edge, Falling Edge, or Either Edge condition may also be set (Note: multiple edges are OR combined). |
Logic Bus Setup
|
Up to 32 digital lines, defined in hexadecimal format |
Interval
|
Define a single digital line, the slope, the condition, and the time period in which the second occurrence of that digital line should occur. Available conditions are <or> |
| Accuracy |
±1 digital sample (based on digital sample rate) |
Certifications
|
CE Approved. Conforms to EN61326-1 and EN61010-1, EN |
| |
|
Physical Dimensions
|
|
Pod Dimensions (WLD)
|
3.8" x 6.3" x 1.2" (9.6 x 16 x 3 cm) |
Pod Weight
|
14 oz. (397 g) |
| Complete System Dimensions (WLD) |
12.5" x
9.8" x 2.5" (32 x 25 x 6.4 cm) |
Ordering Information
| MS-32
Oscilloscope Mixed Signal Option |
Product
Code |
32 Digital Channel Oscilloscope Mixed Signal Option (for WaveSurfer or WaveRunner Series)
|
MS-32
|
32 Digital Channel Oscilloscope Mixed Signal Option (for WavePro or WaveMaster Series)
|
MS-32-DSA
|
MS-32
with license to use on 2 Oscilloscopes
|
MS-32-2LIC
|
MS-32
with license to use on 5 Oscilloscopes
|
MS-32-5LIC
|
| Included
with Standard Configuration |
|
32
Digital Channel Logic Pod with Power Supply
10.6" (27 cm) Lead Set
6 ft. (1.8m) USB 2.0 Cable
Oscilloscope Interface Module with 5 ft. (1.5 m) Cables
Soft Accessory Case
Magnifying Glass (5x)
Printed Operator's Manual (English)
Quick Reference Guide (English)
CE Conformance Certificate
|
|
| Hardware
Options and Accessories |
|
Large
gripper probe set for 0.10" (2.54 mm) pin pitch,
includes 10 probes with color-coded leads |
PK400-1 |
Medium
gripper probe set for 0.04" (1.0 mm) pin pitch,
includes 10 probes with color-coded leads |
PK400-2 |
Small
gripper probe set for 0.008" (0.2 mm) pin pitch,
includes 10 probes with color-coded leads |
PK400-3 |
10"
Digital Lead Set, 32 Digital Channel Lead Set
(for clock speeds < 125 MHz) |
MS-32-STDLEADS |
14"
Digital Lead Set, 32 Digital Channel Lead Set
(for clock speeds < 25 MHz) |
MS-32-STDLEADS-L |
| Mictor
connection cable, 3" long (7.6 cm), 38-pin |
MS-32-Mictor-S |
Mictor
connection cable, 14" long (35.6 cm), 38-pin
(for clock speeds < 100 MHz) |
MS-32-Mictor-L |
Retrofit
GoLogic U36-1 M to MS-32
|
RK-GOLOGIC-MS-32 |
|
|
|
;)
;)
;)
;)
;)
;)
;)
;)
