|
|
DDA 5005A, DDA 3000
DDA 5005A XXL
Quick Specs
- - 3 GHz, 5 GHz Bandwidth
- - 10 GS/s Standard Sample Rate
- - 24 Mpts Memory Standard
 |
 |
< Back to Disk Drive Analyzer Home
Specifications
Vertical
System
|
DDA
5005A
|
Analog
Bandwidth
@ 50Ω (-3 dB) |
5
GHz |
| Input
Channels |
4 |
| Bandwidth
Limiter |
20 MHz; 200 MHz; 1 GHz; 3 GHz; 4 GHz |
| Input
Impedance |
50
Ω ±1.5% |
| Input
Coupling |
DC,
GND |
| Maximum
Input |
2.5
Vrms; ±4 Vpeak |
| Vertical
Resolution |
8
bits; up to 11 bits with
enhanced resolution (ERES) |
| Sensitivity |
2 mV–1 V/div fully variable;
Full bandwidth at ≥ 10mV |
| Offset
Range |
2 mV–99 mV/div: ±750 mV; 100 mV–1 V/div: ±4 V |
| Horizontal
System |
| Timebases |
Internal
timebase common to 4 input channels; An external clock
may be applied at the Auxiliary input |
| Math
& Zoom Traces |
8
math/zoom traces |
| Clock
Accuracy |
≤ 1
ppm @ 0–40 degrees C |
| Time
Interpolator Resolution |
1
ps |
| External
Clock Frequency |
2
GHz maximum; 50 Ω impedance |
| Roll
Mode - Operating Range |
time/div
500 ms - 1000 s/div or sample rate < 100 kS/s
max |
| Acquisition
System |
| Single-Shot
Sample Rate/Ch |
10
GS/s |
| 2
Channel Max |
20
GS/s |
| Maximum
Acquisition Points/Ch |
100 Mpts/ 2 Ch, 50 Mpts/ 4Ch |
| Acquisition Modes |
| Random
Interleaved Sampling (RIS) |
200
GS/s for repetitive signals:
20 ps/div – 1 µs/div |
| Single-Shot |
20 ps/div–10 s/div: For transient and repetitive signals |
| Sequence |
2
– 20,000 segments |
| Intersegment
Time |
Typically
5 µs |
| Acquisition
Processing |
| Averaging |
Summed averaging; Continuous averaging |
| Enhanced
Resolution (ERES) |
From 8.5
to 11 bits vertical resolution |
| Envelope
(Extrema) |
Envelope,
floor, roof for up to 1 million sweeps |
| Triggering
System |
| Modes |
Normal,
Auto, Single, and Stop |
| Sources |
Any
input channel, External, Ext X10, Ext/10, or line; slope
and level unique to each source (except line trigger) |
| Coupling
Mode |
DC |
| Pre-trigger
Delay |
0 –
100% of horizontal time scale |
| Post-trigger
Delay |
0 –
10,000 divisions |
| Hold-off
by Time or Events |
Up to
20s or from 1 to 99 999 999 events |
| Internal
Trigger Range |
±5 div |
| Max
Trigger Frequency |
5 GHz
with Edge Trigger; 750 MHz with SMART Trigger |
| External
Trigger Input Range |
Ext
±0.4; Ext X10 ±0.04; Ext / 10 ±4 V |
| Automatic
Setup |
| Auto
Setup |
Automatically
sets timebase, trigger, and sensitivity to display a
wide range of repetitive signals. |
| Vertical
Find Scale |
Automatically
sets the vertical sensitivity and offset for the
selected channels to display a waveform with maximum
dynamic range. |
| Probes |
| Probes |
A
variety of passive and active probes are optional |
Probe
System:
ProLink with Probus |
Automatically
detects and supports a variety of compatible probes;
Supports ProLink SMA or BNC input adapters |
| Scale
Factors |
Automatically
or manually selected depending on probe used |
| Color
Waveform Display |
| Type |
Color
10.4" flat-panel TFT-LCD with high resolution touch
panel |
| Resolution |
SVGA;
800 x 600 pixels |
| Realtime
Clock |
Dates,
hours, minutes, seconds displayed with waveform |
| Number
of Traces |
Display
a maximum of 8 traces. Simultaneously display channel,
zoom, memory, and math traces. |
| Grid
Styles |
Single,
Dual, Quad, Octal, XY, Single + XY, Dual + XY |
| Waveform
Styles |
Sample
dots joined or dots only |
| Analog
Persistence Display |
| Analog
& Color-Graded Persistence |
Variable
saturation levels; stores each trace’s persistence
data in memory |
| Persistence
Selections |
Select
analog or color positive |
| Trace
Selection |
Activate
Analog Persistence on all or any combination of traces |
| Persistence
Aging Time |
Select
from 500 ms to infinity |
| Sweeps
Displayed |
All
accumulated, or all accumulated with last trace
highlighted |
| Zoom
Expansion Traces |
| Display
up to 4 Zoom and 4 Math/Zoom traces (8 Math/Zoom traces
available with Master Analysis option). |
| Rapid
Signal Processing |
| Processor |
Intel
Pentium with MS Windows Platform |
| Processing
Memory |
512
MBytes |
| Internal
Waveform Memory |
| M1,
M2, M3, M4 Internal Waveform Memory (Store full-length
waveforms with 16 bits/data point) or store to any
number of files limited only by data storage media. |
| Setup
Storage |
| Front
Panel and Instrument Status |
Store
to the internal hard drive, floppy drive, or to a USB
connected peripheral device. |
| Interface |
| Remote
Control |
Full
command set supports front panel controls and internal
functions via GPIB or Ethernet. |
| GPIB
Port (Optional) |
Full
control via IEEE – 488.2 |
| Ethernet
Port |
10/100BaseT
Ethernet interface |
| Floppy
Drive |
Internal,
DOS-format, 3.5" high-density |
| USB
Ports |
Minimum
of 2 USB ports support Windows compatible devices |
| External
Monitor Port Standard |
15-pin
D-Type SVGA-compatible |
| Parallel
Port |
1
standard |
| Auxiliary
Output |
| Signal
Types |
Select
from calibrator or control signals output on front panel |
| Calibrator
Signal |
500 Hz
– 5 MHz square wave or DC Level
0.0 to +0.5 Volts (selectable) into 50 Ω |
| Control
Signals |
Trigger
ready, trigger out, pass/fail status |
| Auxiliary
Input |
| Signal
Types |
Select
from External Trigger or External Clock input on front
panel |
| General |
| Auto
Calibration |
Ensures
specified DC and timing accuracy is maintained for 1
year minimum |
| Power
Requirements |
100–120
V AC at 50/60/400 Hz;
200–240 V AC at 50/60 Hz;
Power
consumption: < 1 kVA , 940 Watts max |
| Physical
Dimensions |
| Dimensions
(HWD) |
264 mm x
397 mm x 491 mm; 10.4" x 15.65" x 19.25"
(height excludes feet) |
| Weight |
18 kg;
39.5 lbs |
| Shipping
Weight |
24 kg;
53 lbs |
| Warranty
and Service |
| 3-year
warranty; calibration recommended annually |
| Optional
service programs include extended warranty, upgrades,
and calibration services. |
| Basic
Triggers |
| Edge/Slope/Line |
Triggers
when signal meets slope and level condition. |
| SMART®Triggers |
| State
or Edge Qualified |
Triggers
on any input source only if a defined state or edge
occurred on another input source. Delay between sources
is selectable by time or events. |
| Dropout |
Triggers
if signal drops out for longer than selected time
between 2 ns and 20 s. |
| Pattern |
Logic
combination (AND, NAND, OR, NOR) of 5 inputs
(4 channels
and external trigger input)
Each source can be high, low, or don’t care.
Trigger
at start or end of the pattern. |
| SMART
Triggers with Exclusion Technology |
| Glitch |
Triggers
on positive or negative glitches with widths selectable
from 600 ps to 20 s or on intermittent faults. |
| Signal
or Pattern Width |
Triggers
on positive or negative pulse widths selectable from 600
ps to 20 s or on intermittent faults. |
| Signal
or Pattern Interval |
Triggers
on intervals selectable between 2 ns and 20 s. |
| Disk
Drive Triggers |
| Sector |
Trigger
on the n'th sector pulse after index. Index and sector
pulse polarity and sector pulse number are selectable. |
| Servo
Gate |
Trigger
on the n'th servo gate after index and every m'th
thereafter. Index and servo gate pulse polarity are
selectable. |
| PES
Trigger |
Trigger
on Position Error Signal (PES) exceeding an adjustable
voltage window. Servo gate can be selected as qualifier. |
| Read
Gate Trigger |
Trigger
on any read gate longer than an adjustable Sector ID
filed length. |
Math
Tools (Standard)
Display up to 8 math function traces (F1 – F8). The
easy-to-use graphical interface simplifies setup of up to two
operations on each function trace. Function traces can be
chained together to perform math-on-math.
| absolute
value |
log
(base 10) |
| average
(summed) |
negate |
| average
(continuous) |
product
(x) |
| difference
(–) |
ratio
(/) |
| differentiate |
reciprocal
(invert) |
enhanced
resolution
(to 11 bits vertical) |
resample
(deskew) |
| envelope |
rescale
(with units) |
| exp
(base e) |
roof |
| exp
(base 10) |
(sin)
x/x |
| FFT
(basic) |
square |
| floor |
square
root |
| identity |
sum (+) |
| integrate |
trend (datalog) |
| log
(base e) |
Auto-correlation |
|
Histogram |
FFT
includes: power averaging, power density, real and imaginary
components, and frequency domain parameters.
Pass/Fail
Testing
Test waveforms by comparing their shape to test templates and
simultaneously check multiple parameters versus selectable
parameter or mask limits. Pass or fail conditions can initiate
actions including document to local or networked files, or
email the image of the failure, saving waveforms, or send a
GPIB SRQ or pulse to trigger another device.
Automated
Disk Drive Measurements
| TAA |
lbase |
ltmn |
msnr |
| TAA+ |
lbsep |
ltmx |
rsnr |
| TAA- |
lmax |
ltot |
m_to_r |
| PW50 |
lmin |
ltpt |
nbph |
| PW50+ |
lnum |
lttp |
nbpw |
| PW50- |
lpp |
ltut |
|
| Resolution |
ltbe |
NLTS |
|
| Overwrite |
ltbp |
ACSN |
|
Standard
Automated Measurements
| amplitude |
peak-to-peak |
| area |
period |
| base |
risetime |
| cycles |
rms |
| cycle
std. deviation |
std.
deviation |
| cycle
mean |
top |
| cycle
median |
width |
| cycle
rms |
last |
| data |
median |
| delay |
number
of points |
| duty
cycle |
phase |
| duration |
time
@ minimum (min.) |
| falltime |
time
@ maximum (max.) |
| frequency |
Δ
delay |
| first |
Δ
time @ level |
| maximum |
Δ
time @ level from trigger |
| mean |
Δ
time from clock to data + (setup time) |
| minimum |
Δ
time from clock to data- (Hold time) |
| +overshoot |
18
Histogram Parameters |
| –overshoot |
|
Jitter
measurement for parameters including: period, cycle-cycle,
frequency, and edge@lv, with JitterTrack up to 200 edges.
Advance
Drive Analysis
Advance Drive Analysis capabilities of the DDA5005A include:
Additional
waveshape analysis capabilities include:
-
FFT
capability includes: power averaging, power density, real
and imaginary components and frequency domain parameters
-
Parameter
Math - add, subtract, multiply or divide two different
parameters
-
User-definable
parameter measurements
-
User-definable
math functions
|
