| |
|
DDA 7 Zi Series
Based on the WavePro 7 Zi Series models, the DDA 7 Zi Series Disk Drive Analyzers are available in 3.5 and 6 GHz models and come equipped with 20 Mpts/ch acquisition memory. Dedicated disk drive measurements, trigger and zooming for failure analysis, and serial data measurement capability with a Disk Drive Analyzer user interface are also standard to address high capacity disk drive designs. Operate in either DDA or SDA mode to analyze the serial data links or the physical media behavior on a hard drive.
- Zoom on multi-zoom on sectors
- One button access to read channel emulation, servo analysis, and disk drive triggers
- Head equalization, channel Emulation, and SAM histograms
- Segmented memory for sector by sector parametric analysis
A Total Solution for Disk Drive Analysis
Maximum Performance
LeCroy Disk Drive Analyzers (DDA) assist data storage design engineers by integrating tools that improve the time to market of new products and accelerate understanding and failure analysis on existing drives. LeCroy continues that tradition with the DDA 7 Zi Series equipped with its powerful Disk Drive Analysis toolset. Capture, view, and analyze the wave shape of high-speed, complex drive signals with speed and integrity.
Data Storage applications are memory intensive as capturing multiple sectors or a complete track of data can be important in troubleshooting a design or characterizing media.
The X-Stream II architecture enables fast and accurate measurements and analysis of disk drive signals. Memory can be extended to 128 Mpts/Ch (256 Mpts/Ch on 2 Ch) using Option L. Both the DDA 760Zi and DDA 735Zi offer the convenience of selectable 50 Ω or 1 MΩ inputs. The standard 20 Mpts of waveform memory and 40 GS/s capture on two channels, means multiple drive sectors can be acquired at once.
Long Memory and Flexibility in Finding Problems
Acquire a head signal up to 6 GHz, and then QuickZoom it from the front panel. The DDA copies and expands the drive signal automatically. Simply scroll horizontally and vertically to examine any sector. Multiple zooms let you view up to eight separate areas of the head signal; each zoom comes in a distinct color. Disk drive parameters let you characterize the pulse width variation or signal-to-noise ratio across a region. Failure Analysis engineers can store and recall golden waveforms and panel setups to compare problem drives with the known good drives. Analog-to-digital converters running at speeds up to 40 GS/s ensure the right sensitivity to measure today’s high-speed read channels. In every DDA, you can run your customer-developed scripts to view the captured signal with the filters matched to your channel and media. Custom user scripts can be created in MATLAB, Visual Basic, Excel or other formats.
Exceptional Trigger and Sequence Performance
The DDA’s disk triggers allow you to set up a series of events in the signal that then cause a trigger. For example, qualify the signal on the index signal and then capture all the sectors of information on the track. As memory is increased in the DDA, more sectors can be captured, with up to 50 picosecond/sample time resolution. Up to 15,000 sectors of data can be gathered with the DDA 7 Zi analyzers. An optional capability, Streaming Sequence, uses the X-Stream II and the fast hardware architecture of the DDA to streamup to 300,000 segments of data to memory; all taken at a high trigger rate.
Natural Graphical Interface
One press on the DDA menu takes you directly to the Disk Drive Analyzer features. The familiar controls on the front panel, coupled with a natural, context-sensitive graphical user-interface, react quickly to your commands. Functionality is exactly where you expect it to be.
The DDA 7 Zi provides one button access to all the tools needed to accurately debug and analyze disk drive operation.
The DDA 7 Zi features:
- 31 custom parameters
- 4 specific drive trigger
- Sector
- Servo Gate
- PES trigger
- Read Gate Trigger
- Advanced drive analysis tools
Advanced Disk Drive analysis tools capabilities include:
- Head Filter Equalizer emulation
- Channel Emulation
- SAM Histograms
- Plot of SAM values
- PES runout analysis
- Analog Compare
Simultaneously connecting low-speed signals, like index and servo gate, and high-speed signals, like read channels has never been easier. With integrated 50 Ω and 1 MΩ inputs on all models, there is no longer a need for expensive adapters.
DDA 735Zi
| Vertical System |
Analog Bandwidth @ 50 Ω (-3 dB)
|
|
3.5 GHz
|
Rise Time (typical)
|
|
120 ps
|
Input Channels
|
|
4
|
Bandwidth Limiters
|
|
20 MHz, 200 MHz
|
Input Impedance
|
|
50 Ω or 1 MΩ||15pF, 10 MΩ || 11 pF with supplied Probe
|
Input Coupling
|
|
1 MΩ: AC, DC, GND; 50 Ω: DC, GND
|
Maximum Input Voltage
|
|
50 Ω: ±5 Vrms
|
Channel-Channel Isolation ProLink Input
|
|
Not Applicable
|
Channel to Channel Isolation ProBus Input
|
|
> 100:1 up to 2.5 GHz, > 30:1 from 2.5 GHz to 3.5 GHz
|
Vertical Resolution
|
|
8 bits; up to 11 bits with enhanced resolution (ERES)
|
Sensitivity
|
|
50 O: 2 mV–1 V/div, fully variable (2-9.99 mV/div via zoom); 1 MO: 2 mV–10 V/div, fully variable
|
DC Gain Accuracy
|
|
±1.5% of full scale
|
Offset Range
|
|
50 Ω:
|
Offset Accuracy
|
|
±(1.5% of full scale + 1.0% of offset value + 1 mV)
|
|
| Horizontal System |
Timebases
|
|
Internal timebase common to 4 input channels; an external clock may be applied at the auxiliary input
|
Time/Division Range
|
|
20 ps/div–1000 s/div (RIS mode: 20 ps/div - 10 ns/div; Roll mode: up to 1000 s/div)
|
Clock Accuracy
|
|
< 1 ppm
|
Jitter Noise Floor
|
|
800 fs (typical)
|
Trigger and Interpolator Jitter
|
|
2 psrms (typical)
|
Sample Rate and Delay Time Accuracy
|
|
< 0.06 / SR + (1 ppm * Reading) (rms)
|
Channel-Channel Deskew Range
|
|
±9 x time/div. setting, 100 ms max., each channel
|
External Timebase Reference (Input)
|
|
10 MHz; 50 Ω impedance, applied at the rear input
|
External Timebase Reference (Output)
|
|
10 MHz; 50 Ω impedance, output at the rear
|
External Sample Clock
|
|
0.1 Hz-100 MHz, 50 Ω or 1 MΩ impedance, applied at the auxiliary input
|
|
| Acquisition System |
Single-Shot Sample Rate/Ch
|
|
40 GS/s on 2 Ch
|
Random Interleaved Sampling (RIS)
|
|
200 GS/s for repetitive signals (20 ps/div to 10 ns/div)
|
Maximum Trigger Rate
|
|
1,000,000 waveforms/second (in Sequence Mode, up to 4 channels)
|
Intersegment Time
|
|
1 μs
|
Standard Memory (4 Ch / 2 Ch) (Number of Segments)
|
|
20 M / 40 M
|
S - Memory Option
|
|
32 M / 64 M
|
M - Memory Option
|
|
64 M / 128 M
|
L - Memory Option
|
|
128 M / 256 M
|
|
| Acquisition Processing |
Averaging
|
|
Summed averaging to 1 million sweeps; continuous averaging to 1 million sweeps
|
Enhanced Resolution (ERES)
|
|
From 8.5 to 11 bits vertical resolution
|
Envelope (Extrema)
|
|
Envelope, floor, or roof for up to 1 million sweeps
|
Interpolation
|
|
Linear or Sin x/x
|
|
| Triggering System |
Modes
|
|
Normal, Auto, Single, and Stop
|
Sources
|
|
Any input channel, Aux, Aux/10, or line; slope and level unique to each source (except line trigger)
|
Coupling Mode
|
|
DC, AC, HFRej, LFRej
|
Pre-trigger Delay
|
|
0–100% of memory size (adjustable in 1% increments of 100 ns)
|
Post-trigger Delay
|
|
0–10,000 divisions in real time mode, limited at slower time/div settings or in roll mode
|
Hold-off by Time or Events
|
|
From 2 ns up to 20 s or from 1 to 99,999,999 events
|
Internal Trigger Range
|
|
±5 div from center
|
Trigger Sensitivity with Edge Trigger (Ch 1–4) ProBus Inputs
|
|
2 div @ < 3.5 GHz
|
Trigger Sensitivity with Edge Trigger (Ch 1–4) ProLink Inputs
|
|
Not Applicable
|
External Trigger Sensitivity
|
|
2 div @ < 1 GHz
|
External Trigger Input Range
|
|
Aux (±0.4 V); Aux/10 (±4 V)
|
Max. Trigger Frequency, SMART Trigger
|
|
2.0 GHz @ = 10 mV/div (minimum signal width setting 250 ps)
|
|
| Basic Triggers |
Edge/ Slope/ Line
|
|
Triggers when signal meets slope (positive, negative, or either) and level condition.
|
TV-Composite Video
|
|
Triggers NTSC or PAL with selectable line and field; HDTV (720p, 1080i, 1080p) with selectable frame rate (50 or 60 Hz) and Line; or CUSTOM with selectable Fields (1-8), Lines (up to 2000), Frame Rates (25, 30, 50, or 60 Hz), Interlacing (1:1, 2:1, 4:1, 8:1), or Synch Pulse Slope (Positive or Negative).
|
|
| SMART Triggers |
State or Edge Qualified
|
|
Triggers on any input source only if a defined state or edge occurred on another input source. Delay between sources is selectable by time or events.
|
Dropout
|
|
Triggers if signal drops out for longer than selected time between 1 ns and 20 s.
|
Pattern
|
|
Logic combination (AND, NAND, OR, NOR) of 5 inputs (4 channels and external trigger input). Each source can be high, low, or don’t care. The High and Low level can be selected independently. Triggers at start or end of the pattern.
|
|
| SMART Triggers with Exclusion Technology |
Glitch
|
|
Triggers on positive or negative glitches with widths selectable as low as 500 ps (depending on oscilloscope bandwidth) to 20 s, or on intermittent faults.
|
Width (Signal or Pattern)
|
|
Triggers on positive or negative widths with widths selectable as low as 200ps (depending on oscilloscope bandwidth) to 20 s, or on intermittent faults.
|
Interval (Signal or Pattern)
|
|
Triggers on intervals selectable between 1 ns and 20 s.
|
Timeout (State/Edge Qualified)
|
|
Triggers on any source if a given state (or transition edge) has occurred on another source.
|
Runt
|
|
Trigger on positive or negative runts defined by two voltage limits and two time limits. Select between 1 ns and 20 ns.
|
Slew Rate
|
|
Trigger on edge rates. Select limits for dV, dt, and slope. Select edge limits between 1 ns and 20 ns.
|
"A" Trigger List
|
|
Edge, Window, Width, Glitch, Pattern, Pattern State, State, Dropout, Interval, Runt, Slew Rate, Serial Data (optional I2C, SPI, UART/RS-232, CAN, LIN, FlexRay)
|
"B" Trigger List
|
|
Edge
|
Exclusion Triggering
|
|
Trigger on intermittent faults by specifying the expected behavior and triggering when that condition is not met
|
Holdoff Between Sequential Triggers
|
|
Arming = Serial & Triggering = Anything, then min. time between events defined by serial pattern length
|
|
| Cascade (Sequence) Triggering |
Capability
|
|
Arm on “A” event, then Trigger on “B” event. Or Arm on “A” event, then Qualify on “B” event, and Trigger on “C” event. Or Arm on “A” event, then Qualify on “B” then “C” event, and Trigger on “D” event
|
Types
|
|
A or B event: Edge, Glitch, Width, Window, Dropout, Interval, Runt, Slew Rate, or Pattern (analog) C or D event: Edge or Pattern
|
Holdoff
|
|
Delay between A and B, B and C, C and D, are all selectable by time or number of events
|
Reset
|
|
Reset between A and B, B and C, C and D, are all selectable in time
|
|
| High Speed Serial Protocol Triggering |
Data Rates
|
|
100 Mb/s - 1.25 Gb/s
|
Pattern Length
|
|
80 bits, NRZ or 8b10b
|
Clock and Data Outputs
|
|
400mVp-p (typical) AC coupled
|
Clock Recovery Jitter
|
|
2 ps rms + 0.3% Unit Interval rms for PRBS data patterns with 50% transition density (Typical)
|
Clock Recovery Tracking/ Acquisition Range
|
|
50 Mb/s - 1.25 Gb/s
|
Hardware Clock Recovery Loop BW
|
|
PLL Loop BW = Fbaud/5500, 100 Mb/s to 1.25 Gb/s (Typical)
|
|
| Low Speed Serial Protocol Triggering (Optional) |
Optionally available
|
|
I2C, SPI (SPI, SSPI, SIOP), UART-RS232, CAN, LIN, FlexRay
|
|
| Color Waveform Display |
Type
|
|
Color 15.3" flat panel TFT-Active Matrix LCD with high resolution touch screen
|
Resolution
|
|
WXGA; 1280 x 768 pixels
|
Number of traces
|
|
Display a maximum of 8 traces. Simultaneously display channel, zoom, memory and math traces.
|
Grid Styles
|
|
Auto, Single, Dual, Quad, Octal, X-Y, Single+X-Y, Dual+X-Y
|
Waveform Representation
|
|
Sample dots joined, or sample dots only
|
|
| Internal Waveform Memory |
Internal Waveform Memory
|
|
4 active waveform memory traces (M1-M4) store 16 bit/point full length waveforms. Waveforms can be stored to any number of files limited only by the data storage media capacity.
|
|
| WaveStream™ Fast Viewing Mode |
Intensity
|
|
256 Intensity Levels, 1–100% adjustable via front panel control
|
Number of Channels
|
|
up to 4 simultaneously
|
Max Sampling Rate
|
|
40 GS/s (20 GS/s for WavePro 710Zi without WPZi-1GHZ-4X20GS option)
|
Waveforms
|
|
up to 2500 Waveforms/ second
|
|
| Automatic Setup |
Auto Setup
|
|
Automatically sets timebase, trigger, and sensitivity to display a wide range of repetitive signals
|
Find Vertical Scale
|
|
Automatically sets the vertical sensitivity and offset for the selected channel to display a waveform with the maximum dynamic range
|
|
| Probes |
Probes
|
|
Qty. (4) ÷10 Passive Probes
|
Probe System: ProBus
|
|
Probus (and ProLink on 4-6 GHz models). Automatically detects and supports a variety of compatible probes
|
Scale Factors
|
|
Automatically or manually selected depending on probe used
|
Calibration Output
|
|
1kHz square wave, 1Vp-p (typical), output to probe hook
|
|
| Analog Persistence Display |
Analog and Color-Graded Persistence
|
|
Variable saturation levels; stores each trace’s persistence data in memory
|
Trace Selection
|
|
Activate persistence on all or any combination of traces
|
Sweep Display Modes
|
|
All accumulated, or all accumulated with last trace highlighted
|
Persistence Types
|
|
Select analog, color, or three-dimensional
|
Persistence Aging
|
|
Select from 500 ms to infinity
|
|
| Setup and Waveform Storage |
Front Panel and Instrument Status
|
|
Store to the internal hard drive or to a USB-connected peripheral device.
|
|
| High Speed Digitizer Output (Option) |
Type
|
|
LeCroy LSIB
|
Transfer Rate
|
|
Up to 325 MB/s (Typical)
|
Output Protocol
|
|
PCI Express, Gen 1 (4 lanes utilized for data transfer)
|
Control Protocol
|
|
TCP/IP
|
Command Set
|
|
Via Windows Automation, or via LeCroy Remote Command Set
|
|
| Processor/CPU |
Type
|
|
Intel® CoreTM 2 Quad, 2.5 GHz (or better)
|
Processor Memory
|
|
4 GB standard, up to 8 GB optional
|
Operating System
|
|
Microsoft Windows® Vista Business Edition (64-bit) with SP1
|
Oscilloscope Operating Software
|
|
Entire instrument including any installed optional applications packages operates within a single (X-Stream) Windows application
|
Real Time Clock
|
|
Date and time displayed with waveform an in hardcopy files. SNTP support to synchronize to precision internal clocks.
|
|
| Zoom Expansion Traces |
Zoom Expansion Traces
|
|
Display up to 4 Zoom and 8 Math/Zoom traces
|
|
| Interface |
Remote Control
|
|
Via Windows Automation, or via LeCroy Remote Command Set
|
GPIB Port (optional)
|
|
Supports IEEE – 488.2
|
LSIB Port (optional)
|
|
Supports PCIe Gen1 x4 protocol with LeCroy supplied API
|
USB Device Port (optional)
|
|
Type-B
|
Ethernet Port
|
|
Supports 10/100/1000 BaseT Ethernet interface (RJ45 port)
|
USB Ports
|
|
minimum 6 total (incl. 3 front panel) USB 2.0 ports support Windows compatible devices
|
External Monitor Port
|
|
15-pin D-Type WXGA compatible to support customer-supplied external monitor. DVI connector to support LeCroy Zi-EXTDISP-15 additional touch screen display accessory. Includes support for extended desktop operation with optional LeCroy or other second monitor
|
Serial Port
|
|
2 standard
|
Peripheral Bus
|
|
LeCroy LBUS standard
|
|
| Auxiliary Input |
Signal Types
|
|
Select External Trigger
|
Coupling
|
|
50 Ω: DC; 1 MΩ: AC, DC, GND
|
Max. Input Voltage
|
|
50 Ω: 5 Vrms; 1 MΩ: 250 V (Peak AC < 10 kHz + DC)
|
|
| Auxiliary Output |
Signal Types
|
|
Select from calibrator, control signals or Off
|
Calibrator Signal
|
|
5 Hz–5 MHz square wave or DC level; 0.0 to 500 mV into 50 Ω (0–1 V into 1 MΩ)
|
Control Signals
|
|
Trigger enabled, trigger out, pass/fail status
|
|
| General |
Auto Calibration
|
|
Ensures specified DC and timing accuracy is maintained for 1 year minimum.
|
|
| Power Requirements |
Voltage
|
|
100–240 VAC ±10% at 45-66 Hz; 100-120 VAC ±10% at 380-420 Hz; Automatic AC Voltage Selection
|
Max. Power Consumption
|
|
850 W/850 VA
|
|
| Environmental and Safety |
Temperature (Operating)
|
|
+5 °C to +40 °C including CD-RW/DVD-ROM drive
|
Temperature (Non-Operating)
|
|
–20 °C to +60 °C
|
Humidity (Operating)
|
|
5% to 80% relative humidity (non-condensing) up to +31 °C.
|
Humidity (Non-Operating)
|
|
5% to 95% relative humidity (non-condensing) as tested per MIL-PRF-28800F
|
Altitude (Operating)
|
|
Up to 10,000 ft. (3048 m) at or below +25 °C
|
Altitude (Non-Operating)
|
|
Up to 40,000 ft. (12,192 m)
|
Random Vibration (Operating)
|
|
0.5 grms overall level, 5 Hz to 500 Hz, 10 minutes in each of three orthogonal axes, 30 minutes total
|
Random Vibration (Non-Operating)
|
|
2.0 grms overall level, 5 Hz to 500 Hz, 10 minutes in each of three orthogonal axes, 30 minutes total
|
Functional Shock
|
|
20 g peak, half sine, 11 ms pulse, 3 shocks (positive and negative) in each of three orthogonal axes, 18 shocks total
|
|
| Physical Dimensions |
Dimensions (HWD)
|
|
14"H x 18.4"W x 11.4"D (355 x 467 x 289 mm)
|
Weight
|
|
39.5 lbs. (18 kg)
|
Shipping Weight
|
|
28.2 kg; 62 lbs.
|
|
| Certifications |
Certifications
|
|
CE Compliant, UL and cUL listed; conforms to EN 61326-1, EN 61010-1, UL 61010-1 2nd edition, and CSA C22.2 No. 61010-1-04
|
|
| Warranty and Service |
Warranty and Service
|
|
3-year warranty; calibration recommended annually.
|
|
DDA 760Zi
| Vertical System |
Analog Bandwidth @ 50 Ω (-3 dB)
|
|
6 GHz
|
Rise Time (typical)
|
|
70 ps
|
Input Channels
|
|
4
|
Bandwidth Limiters
|
|
20 MHz, 200 MHz
|
Input Impedance
|
|
50 Ω or 1 MΩ||15pF, 10 MΩ || 11 pF with supplied Probe
|
Input Coupling
|
|
1 MΩ: AC, DC, GND; 50 Ω: DC, GND
|
Maximum Input Voltage
|
|
50 Ω (ProBus): ±5 Vrms
|
Channel-Channel Isolation ProLink Input
|
|
> 200:1 up to 2 GHz, > 50:1 from 2 GHz to 4 GHz, > 20:1 from 4 GHz to 6 GHz
|
Channel to Channel Isolation ProBus Input
|
|
> 100:1 up to 2.5 GHz, > 30:1 from 2.5 GHz to 3.5 GHz
|
Vertical Resolution
|
|
8 bits; up to 11 bits with enhanced resolution (ERES)
|
Sensitivity
|
|
50 Ω: 2 mV–1 V/div, fully variable (2-9.99 mV/div via zoom); 1 MΩ: 2 mV–10 V/div, fully variable
|
DC Gain Accuracy
|
|
±1.5% of full scale
|
Offset Range
|
|
50 Ω:
|
Offset Accuracy
|
|
±(1.5% of full scale + 1.0% of offset value + 1 mV)
|
|
| Horizontal System |
Timebases
|
|
Internal timebase common to 4 input channels; an external clock may be applied at the auxiliary input
|
Time/Division Range
|
|
20 ps/div–1000 s/div (RIS mode: 20 ps/div - 10 ns/div; Roll mode: up to 1000 s/div)
|
Clock Accuracy
|
|
< 1 ppm
|
Jitter Noise Floor
|
|
560 fs (typical)
|
Trigger and Interpolator Jitter
|
|
1 psrms (typical)
|
Sample Rate and Delay Time Accuracy
|
|
< 0.06 / SR + (1 ppm * Reading) (rms)
|
Channel-Channel Deskew Range
|
|
±9 x time/div. setting, 100 ms max., each channel
|
External Timebase Reference (Input)
|
|
10 MHz; 50 Ω impedance, applied at the rear input
|
External Timebase Reference (Output)
|
|
10 MHz; 50 Ω impedance, output at the rear
|
External Sample Clock
|
|
0.1 Hz-100 MHz, 50 Ω or 1 MΩ impedance, applied at the auxiliary input
|
|
| Acquisition System |
Single-Shot Sample Rate/Ch
|
|
40 GS/s on 2 Ch
|
Random Interleaved Sampling (RIS)
|
|
200 GS/s for repetitive signals (20 ps/div to 10 ns/div)
|
Maximum Trigger Rate
|
|
1,000,000 waveforms/second (in Sequence Mode, up to 4 channels)
|
Intersegment Time
|
|
1 μs
|
Standard Memory (4 Ch / 2 Ch) (Number of Segments)
|
|
20 M / 40 M
|
S - Memory Option
|
|
32 M / 64 M
|
M - Memory Option
|
|
64 M / 128 M
|
L - Memory Option
|
|
128 M / 256 M
|
|
| Acquisition Processing |
Averaging
|
|
Summed averaging to 1 million sweeps; continuous averaging to 1 million sweeps
|
Enhanced Resolution (ERES)
|
|
From 8.5 to 11 bits vertical resolution
|
Envelope (Extrema)
|
|
Envelope, floor, or roof for up to 1 million sweeps
|
Interpolation
|
|
Linear or Sin x/x
|
|
| Triggering System |
Modes
|
|
Normal, Auto, Single, and Stop
|
Sources
|
|
Any input channel, Aux, Aux/10, or line; slope and level unique to each source (except line trigger)
|
Coupling Mode
|
|
DC, AC, HFRej, LFRej
|
Pre-trigger Delay
|
|
0–100% of memory size (adjustable in 1% increments of 100 ns)
|
Post-trigger Delay
|
|
0–10,000 divisions in real time mode, limited at slower time/div settings or in roll mode
|
Hold-off by Time or Events
|
|
From 2 ns up to 20 s or from 1 to 99,999,999 events
|
Internal Trigger Range
|
|
±5 div from center
|
Trigger Sensitivity with Edge Trigger (Ch 1–4) ProBus Inputs
|
|
2 div @ < 3.5 GHz
|
Trigger Sensitivity with Edge Trigger (Ch 1–4) ProLink Inputs
|
|
2 div @ < 6 GHz
|
External Trigger Sensitivity
|
|
2 div @ < 1 GHz
|
External Trigger Input Range
|
|
Aux (±0.4 V); Aux/10 (±4 V)
|
Max. Trigger Frequency, SMART Trigger
|
|
2.0 GHz @ = 10 mV/div
|
|
| Basic Triggers |
Edge/ Slope/ Line
|
|
Triggers when signal meets slope (positive, negative, or either) and level condition.
|
TV-Composite Video
|
|
Triggers NTSC or PAL with selectable line and field; HDTV (720p, 1080i, 1080p) with selectable frame rate (50 or 60 Hz) and Line; or CUSTOM with selectable Fields (1-8), Lines (up to 2000), Frame Rates (25, 30, 50, or 60 Hz), Interlacing (1:1, 2:1, 4:1, 8:1), or Synch Pulse Slope (Positive or Negative).
|
|
| SMART Triggers |
State or Edge Qualified
|
|
Triggers on any input source only if a defined state or edge occurred on another input source. Delay between sources is selectable by time or events.
|
Dropout
|
|
Triggers if signal drops out for longer than selected time between 1 ns and 20 s.
|
Pattern
|
|
Logic combination (AND, NAND, OR, NOR) of 5 inputs (4 channels and external trigger input). Each source can be high, low, or don’t care. The High and Low level can be selected independently. Triggers at start or end of the pattern.
|
|
| SMART Triggers with Exclusion Technology |
Glitch
|
|
Triggers on positive or negative glitches with widths selectable as low as 500 ps (depending on oscilloscope bandwidth) to 20 s, or on intermittent faults.
|
Width (Signal or Pattern)
|
|
Triggers on positive or negative widths with widths selectable as low as 200ps (depending on oscilloscope bandwidth) to 20 s, or on intermittent faults.
|
Interval (Signal or Pattern)
|
|
Triggers on intervals selectable between 1 ns and 20 s.
|
Timeout (State/Edge Qualified)
|
|
Triggers on any source if a given state (or transition edge) has occurred on another source.
|
Runt
|
|
Trigger on positive or negative runts defined by two voltage limits and two time limits. Select between 1 ns and 20 ns.
|
Slew Rate
|
|
Trigger on edge rates. Select limits for dV, dt, and slope. Select edge limits between 1 ns and 20 ns.
|
"A" Trigger List
|
|
Edge, Window, Width, Glitch, Pattern, Pattern State, State, Dropout, Interval, Runt, Slew Rate, Serial Data (optional I2C, SPI, UART/RS-232, CAN, LIN, FlexRay)
|
"B" Trigger List
|
|
Edge
|
Exclusion Triggering
|
|
Trigger on intermittent faults by specifying the expected behavior and triggering when that condition is not met
|
Holdoff Between Sequential Triggers
|
|
Arming = Serial & Triggering = Anything, then min. time between events defined by serial pattern length
|
|
| Cascade (Sequence) Triggering |
Capability
|
|
Arm on “A” event, then Trigger on “B” event. Or Arm on “A” event, then Qualify on “B” event, and Trigger on “C” event. Or Arm on “A” event, then Qualify on “B” then “C” event, and Trigger on “D” event
|
Types
|
|
A or B event: Edge, Glitch, Width, Window, Dropout, Interval, Runt, Slew Rate, or Pattern (analog) C or D event: Edge or Pattern
|
Holdoff
|
|
Delay between A and B, B and C, C and D, are all selectable by time or number of events
|
Reset
|
|
Reset between A and B, B and C, C and D, are all selectable in time
|
|
| High Speed Serial Protocol Triggering |
Data Rates
|
|
100 Mb/s - 3.125 Gb/s
|
Pattern Length
|
|
80 bits, NRZ or 8b10b
|
Clock and Data Outputs
|
|
400mVp-p (typical) AC coupled
|
Clock Recovery Jitter
|
|
2 ps rms + 0.3% Unit Interval rms for PRBS data patterns with 50% transition density (Typical)
|
Clock Recovery Tracking/ Acquisition Range
|
|
50 Mb/s - 2.7 Gb/s
|
Hardware Clock Recovery Loop BW
|
|
PLL Loop BW = Fbaud/5500, 100 Mb/s to 1.25 Gb/s (Typical)
|
|
| Low Speed Serial Protocol Triggering (Optional) |
Optionally available
|
|
I2C, SPI (SPI, SSPI, SIOP), UART-RS232, CAN, LIN, FlexRay
|
|
| Color Waveform Display |
Type
|
|
Color 15.3" flat panel TFT-Active Matrix LCD with high resolution touch screen
|
Resolution
|
|
WXGA; 1280 x 768 pixels
|
Number of traces
|
|
Display a maximum of 8 traces. Simultaneously display channel, zoom, memory and math traces.
|
Grid Styles
|
|
Auto, Single, Dual, Quad, Octal, X-Y, Single+X-Y, Dual+X-Y
|
Waveform Representation
|
|
Sample dots joined, or sample dots only
|
|
| Internal Waveform Memory |
Internal Waveform Memory
|
|
4 active waveform memory traces (M1-M4) store 16 bit/point full length waveforms. Waveforms can be stored to any number of files limited only by the data storage media capacity.
|
|
| WaveStream™ Fast Viewing Mode |
Intensity
|
|
256 Intensity Levels, 1–100% adjustable via front panel control
|
Number of Channels
|
|
up to 4 simultaneously
|
Max Sampling Rate
|
|
40 GS/s (20 GS/s for WavePro 710Zi without WPZi-1GHZ-4X20GS option)
|
Waveforms
|
|
up to 2500 Waveforms/ second
|
|
| Automatic Setup |
Auto Setup
|
|
Automatically sets timebase, trigger, and sensitivity to display a wide range of repetitive signals
|
Find Vertical Scale
|
|
Automatically sets the vertical sensitivity and offset for the selected channel to display a waveform with the maximum dynamic range
|
|
| Probes |
Probes
|
|
Qty. (4) ÷10 Passive Probes
|
Probe System: ProBus
|
|
Probus (and ProLink on 4-6 GHz models). Automatically detects and supports a variety of compatible probes
|
Scale Factors
|
|
Automatically or manually selected depending on probe used
|
Calibration Output
|
|
1kHz square wave, 1Vp-p (typical), output to probe hook
|
|
| Analog Persistence Display |
Analog and Color-Graded Persistence
|
|
Variable saturation levels; stores each trace’s persistence data in memory
|
Trace Selection
|
|
Activate persistence on all or any combination of traces
|
Sweep Display Modes
|
|
All accumulated, or all accumulated with last trace highlighted
|
Persistence Types
|
|
Select analog, color, or three-dimensional
|
Persistence Aging
|
|
Select from 500 ms to infinity
|
|
| Setup and Waveform Storage |
Front Panel and Instrument Status
|
|
Store to the internal hard drive or to a USB-connected peripheral device.
|
|
| High Speed Digitizer Output (Option) |
Type
|
|
LeCroy LSIB
|
Transfer Rate
|
|
Up to 325 MB/s (Typical)
|
Output Protocol
|
|
PCI Express, Gen 1 (4 lanes utilized for data transfer)
|
Control Protocol
|
|
TCP/IP
|
Command Set
|
|
Via Windows Automation, or via LeCroy Remote Command Set
|
|
| Processor/CPU |
Type
|
|
Intel® CoreTM 2 Quad, 2.5 GHz (or better)
|
Processor Memory
|
|
4 GB standard, up to 8 GB optional
|
Operating System
|
|
Microsoft Windows® Vista Business Edition (64-bit) with SP1
|
Oscilloscope Operating Software
|
|
Entire instrument including any installed optional applications packages operates within a single (X-Stream) Windows application
|
Real Time Clock
|
|
Date and time displayed with waveform an in hardcopy files. SNTP support to synchronize to precision internal clocks.
|
|
| Zoom Expansion Traces |
Zoom Expansion Traces
|
|
Display up to 4 Zoom and 8 Math/Zoom traces
|
|
| Interface |
Remote Control
|
|
Via Windows Automation, or via LeCroy Remote Command Set
|
GPIB Port (optional)
|
|
Supports IEEE – 488.2
|
LSIB Port (optional)
|
|
Supports PCIe Gen1 x4 protocol with LeCroy supplied API
|
USB Device Port (optional)
|
|
Type-B
|
Ethernet Port
|
|
Supports 10/100/1000 BaseT Ethernet interface (RJ45 port)
|
USB Ports
|
|
minimum 6 total (incl. 3 front panel) USB 2.0 ports support Windows compatible devices
|
External Monitor Port
|
|
15-pin D-Type WXGA compatible to support customer-supplied external monitor. DVI connector to support LeCroy Zi-EXTDISP-15 additional touch screen display accessory. Includes support for extended desktop operation with optional LeCroy or other second monitor
|
Serial Port
|
|
2 standard
|
Peripheral Bus
|
|
LeCroy LBUS standard
|
|
| Auxiliary Input |
Signal Types
|
|
Select External Trigger
|
Coupling
|
|
50 Ω: DC; 1 MO: AC, DC, GND
|
Max. Input Voltage
|
|
50 Ω: 5 Vrms; 1 MO: 250 V (Peak AC < 10 kHz + DC)
|
|
| Auxiliary Output |
Signal Types
|
|
Select from calibrator, control signals or Off
|
Calibrator Signal
|
|
5 Hz–5 MHz square wave or DC level; 0.0 to 500 mV into 50 Ω (0–1 V into 1 MΩ)
|
Control Signals
|
|
Trigger enabled, trigger out, pass/fail status
|
|
| General |
Auto Calibration
|
|
Ensures specified DC and timing accuracy is maintained for 1 year minimum.
|
|
| Power Requirements |
Voltage
|
|
100–240 VAC ±10% at 45-66 Hz; 100-120 VAC ±10% at 380-420 Hz; Automatic AC Voltage Selection
|
Max. Power Consumption
|
|
850 W/850 VA
|
|
| Environmental and Safety |
Temperature (Operating)
|
|
+5 °C to +40 °C including CD-RW/DVD-ROM drive
|
Temperature (Non-Operating)
|
|
–20 °C to +60 °C
|
Humidity (Operating)
|
|
5% to 80% relative humidity (non-condensing) up to +31 °C.
|
Humidity (Non-Operating)
|
|
5% to 95% relative humidity (non-condensing) as tested per MIL-PRF-28800F
|
Altitude (Operating)
|
|
Up to 10,000 ft. (3048 m) at or below +25 °C
|
Altitude (Non-Operating)
|
|
Up to 40,000 ft. (12,192 m)
|
Random Vibration (Operating)
|
|
0.5 grms overall level, 5 Hz to 500 Hz, 10 minutes in each of three orthogonal axes, 30 minutes total
|
Random Vibration (Non-Operating)
|
|
2.0 grms overall level, 5 Hz to 500 Hz, 10 minutes in each of three orthogonal axes, 30 minutes total
|
Functional Shock
|
|
20 g peak, half sine, 11 ms pulse, 3 shocks (positive and negative) in each of three orthogonal axes, 18 shocks total
|
|
| Physical Dimensions |
Dimensions (HWD)
|
|
14"H x 18.4"W x 11.4"D (355 x 467 x 289 mm)
|
Weight
|
|
39.5 lbs. (18 kg)
|
Shipping Weight
|
|
28.2 kg; 62 lbs.
|
|
| Certifications |
Certifications
|
|
CE Compliant, UL and cUL listed; conforms to EN 61326-1, EN 61010-1, UL 61010-1 2nd edition, and CSA C22.2 No. 61010-1-04
|
|
| Warranty and Service |
Warranty and Service
|
|
3-year warranty; calibration recommended annually.
|
|
Memory Options
| | DDAZi-L-128 | 128 Mpt/Ch (256 Mpt/Ch Interleaved) Memory Option for DDA Zi. Includes an additional 4 GB of RAM (8 GB total) | | DDAZi-M-64 | 64 Mpt/Ch (128 Mpt/Ch Interleaved) Memory Option for DDA Zi. Includes an additional 4 GB of RAM (8 GB total) | | DDAZi-S-32 | 32 Mpt/Ch (64 Mpt/Ch Interleaved) Memory Option for DDA Zi. Includes an additional 2 GB of RAM (4 GB total) | Serial Trigger and Decode
| | WPZi-FlexrayBus TD | FlexRay Bus Trigger & Decode Option for WavePro Zi Series Oscilloscopes | | WPZi-FlexRayBus TDP | FlexRay Bus Trigger, Decode, and Physical Layer Test Option for WavePro Zi Series Oscilloscopes | | WPZi-HSPT | 50 Mb/s to 3.125 Gb/s High Speed Serial Trigger Option for 4-6 GHz Oscilloscopes & Disk Drive Analyzers | | WPZi-I2Cbus TD | I2C Bus Trigger & Decode Option for WavePro Zi Series Oscilloscopes | | WPZi-LINbus TD | LIN Bus Trigger & Decode Option for WavePro Zi Series Oscilloscopes | | WPZi-MSPT | 50 Mb/s to 1.25 Gb/s Medium Speed Serial Trigger Option for 2.5-3.5 GHz Oscilloscopes & Disk Drive Analyzers | | WPZi-SPIbus TD | SPI Bus Trigger & Decode Option for WavePro Zi Series Oscilloscopes | | WPZi-UART-RS232bus TD | UART and RS232 Bus Trigger & Decode Option for WavePro Zi Series Oscilloscopes | Serial Data Communications Testing Software
| | QPHY-ENET | QualiPHY Ethernet Application Software | | QPHY-HDMI | QualiPHY Enabled HDMI Software Option (TF-HDMI-3.3V-QUADPAK required;WavePro 760Zi requires SDA II option) | | QPHY-PCIe | PCIe Gen1 Compliance and Development Software | | QPHY-SATA | QualiPHY Enabled SATA Software Option | | QPHY-USB | USB Application Software Package | | QPHY-UWB | WiMedia UWB Transmitter Measurement Software Option | General Purpose Software
| | WPZi-AORM | Advanced Optical Recording Measurement Package for WavePro Zi Series | | WPZi-EMC | EMC Pulse Parameter Software Package for WavePro Zi Series | | WPZi-EYEDRII | Eye Doctor II Advanced Signal Integrity Tools for WavePro 7 Zi Oscilloscopes, SDA 7 Zi Serial Data Analyzers, and DDA 7 Zi Disk Drive Analyzers | | WPZi-SPECTRUM | Spectrum Analyzer and Advanced FFT Option for WavePro Zi Series | | WPZi-XDEV | Developer's Tool Kit Option for WavePro Zi Series | Digital Filtering Software
| | WPZi-DFP2 | Digital Filter Software Package for WavePro Zi Series | Jitter Analysis Software
| | WPZi-JTA2 | Jitter Timing and Analysis Software Package for WavePro Zi Series | CAN Bus Testing
| | WPZi-CANbus TD | CAN Bus Trigger & Decode Option for WavePro Zi Series Oscilloscopes | | WPZi-CANbus TDM | CAN Bus Trigger, Decode, and Measure Option for WavePro Zi Series Oscilloscopes | Mixed Signal Test Solutions
| | MS-250 | 250 MHz Maximum Input Frequency, 18 Channels, 10 Mpts/ch Mixed Signal Oscilloscope Option | | MS-500 | 500 MHz Maximum Input Frequency, 18 Channels, 50 Mpts/ch Mixed Signal Oscilloscope Option | | MS-500-36 | 250 MHz Maximum Input Frequency, 36 Channels, 25 Mpts/ch Mixed Signal Oscilloscope Option | | MSO-DLS-18 | Digital Lead Set, D0-D17 | | MSO-DLS-36 | Digital Lead Set, D18-D35 | | MSO-GND-EXTEND | MSO Ground Extenders | | MSO-GND-LEAD | MSO Flying Ground Lead | | MSO-LBUS | LeCroy Bus Cable | | MSO-MICTOR | Mictor Cable, D0-D35 | Communications Testing Fixtures
| | TF-DSQ | Probe Deskew and Calibration Fixture | | TF-ENET-B | 10/100/1000Base-T Compliance Test Fixture | | TF-ET | Telecom Adaptor Kit 100Ω, 120Ω, 75Ω | | TF-HDMI-3.3V-QUADPAK | HDMI Pull-Up Terminator Quad Pack – for Use with the Efficere ET-HDMI-TPS-S Test Fixture | | TF-SATA-C | SATA Compliance Test Fixture (*WavePro 7 Zi and WaveMaster 8 Zi class oscilloscopes require the SDA II software option; **20M memory required) | | TF-SATA-C-Kit | SATA Compliance Test Kit (*WavePro 7 Zi and WaveMaster 8 Zi class oscilloscopes require the SDA II software option; **20M memory required) | | TF-USB-B | USB 2.0 Testing Compliance Test Fixture | Differential Amplifiers
| | DA1855A | DA1855A, 100 MHz Differential Amplifier with fast over drive recovery, calibrated offset, and selectable LP filters | | DA1855A-PR2 | 2 Ch, 100 MHz Differential Amplifier with fast over drive recovery, calibrated offset, and selectable LP filters | | DA1855A-PR2-RM | Rack mountable version of the DA1855A-PR2 | Storage Devices
| | GPIB-2 | GPIB Option for LeCroy oscilloscope. Half-height card with custom connector. | | LSIB-1 | High speed PCIe Gen1 x4 digitizer output for LeCroy oscilloscope. Half-height card with custom connector | | WPZi-2-UPG-8GBRAM | Upgrade from 2 GB to 8 GB CPU RAM | | WPZi-200GB-HD | Upgrade from standard size hard drive to 200 GB hard drive | | WPZi-200GB-RHD-02 | Additional 200 GB Hard Drive for WPZi. Includes Windows Vista OS, LeCroy oscilloscope software and critical scope operational file duplicates. | | WPZi-4-UPG-8GBRAM | Upgrade from 4 GB to 8 GB CPU RAM | Miscellaneous Accessories
| | FRONT-COVER-1 | Replacement Protective Front Cover for WavePro Zi Series | | KYBD-1 | Keyboard | | LSIB-CABLE-3M | PCI Express x 4 3-meter cable with x4 cable connectors included | | LSIB-CABLE-7M | PCI Express x 4 7-meter cable with x4 cable connectors include | | LSIB-HOSTBOARD | PCI Express x4 Host Interface Board for desktop PC | | LSIB-HOSTCARD | PCI Express x1 Express Card Host Interface for laptop Express Card slot | | POUCH-1 | Replacement Accessory Pouch | Rackmounts, Carts and Cases
| | OC1021 | OC1021 scope cart is sturdy and mobile | | OC1024 | OC1024 scope cart is sturdy and mobile | | RACKMOUNT-1 | Rack-mount accessory for converting a WavePro Zi series oscilloscope to an 8U rack-mounted package | | WPZi-HARDCASE | Hard carrying case for all WavePro Zi Series oscilloscopes | | WPZi-SOFTCASE | Soft carrying case for all WavePro Zi Series oscilloscopes | Warranty & Calibration
| | WPZi-C5 | Five Year NIST Calibration | | WPZi-C5/MIL | Five Year MIL Calibration | | WPZi-CC | NIST Traceable Calibration | | WPZi-CCM | MIL STD Calibration | | WPZi-CCMIL | MIL Std. Traceable Calibration | | WPZi-EW | 1 Year Extended Warranty | | WPZi-EW2 | 2 Year Extended Warranty | | WPZi-T5 | Five Year Warranty & NIST Calibration | | WPZi-T5/MIL | Five Year Warranty & MIL Calibration |
Differential Probes
| | ADP300 | High-Voltage Active Differential Probe | | ADP305 | High-Voltage Differential Probes From LeCroy | | AP031 | 15 MHz Differential Probe | | AP033 | 500 MHz Active Differential Probe | | AP034 | 1 GHz Active Differential Probe | | D300A-AT | WaveLink 4 GHz Differential Probe with Adjustable Tip Module | | D310 | WaveLink 3.5 GHz Differential probe module 2.5V | | D320 | WaveLink 3.5 GHz Differential probe module 5V | | D350ST | WaveLink 4 GHz, 5 V Differential with Small Tip Module | | D500PT | WaveLink 6 GHz Differential Positioner Mounted Tip Module | | D600A-AT | WaveLink 7.5 GHz Differential Probe with Adjustable Tip Module | | D600ST | WaveLink 7 GHz Differential Probe with Small Tip Module (includes D6000ST-SI, D600ST-QC, D600ST-SP) | | D610 | WaveLink 6 GHz Differential probe module 2.5V | | D620 | WaveLink 6 GHz Differential probe module 5V | | Dx10-PT | Replacement Dx10-PT Tip with Qty. 4 Pogo Pin Tips and Qty. 2 Sockets | | Dx20-PT | Replacement Dx20-PT Tip with Qty. 4 Pogo Pin Tips and Qty. 2 Sockets | | WL-Pbus | WaveLink ProBus probe body = 3.5 GHz | | WL-PLink | WaveLink ProLink probe body >3.5 GHz | | WL300 | WaveLink ProBus Probe Body | | WL600 | WaveLink ProLink Probe Body | Active Voltage Probes
| | HFP2500 | 2.5 GHz Active Voltage Probe | Current Probes
| | AP015 | 30 Amps, 50MHz BW Current Probe - AC/DC, 50 Amp Peak Pulse | | CP030 | 30 Amps, 50 MHz BW Current Probe - AC/DC , 50 Amp Peak Pulse | | CP031 | 30 Amps, 100 MHz BW Current Probe - AC/DC , 50 Amp Peak Pulse | | CP150 | 150 Amps, 10 MHz BW Current Probe - AC/DC , 500 Amp Peak Pulse | | CP500 | 500 Amps, 2 MHz BW Current Probe - AC/DC , 700 Amp Peak | High Voltage Probes
| | PPE1.2KV | 10:1/100:1 200/300 MHz 5M Ohm/100M Ohm | | PPE20KV | 1000:1 100 MHz 100M Ohm High-Voltage Probe | | PPE2KV | 100:1 400 MHz 100M Ohm High Voltage Probe | | PPE4KV | 100:1 400 MHz 100M Ohm High-Voltage Probe | | PPE5KV | 100:1 400 MHz 100M Ohm High-Voltage Probe | | PPE6KV | 1000:1 400 MHz 5M Ohm High-Voltage Probe | Passive Probes
| | PP007-WR-1 | Passive Probe, 500 MHz, 2.5mm tip | | PP011-1 | PP011 Passive Probe | ZS Series High Impedance Active Probes
| | ZS1000 | 1 GHz, 1 MΩ, 0.9 pF Active Probe | | ZS1000-QUADPAK | Set of 4 ZS1000 Active Probes | | ZS1500 | 1.5 GHz, 1 MΩ, 0.9 pF Active Probe | | ZS1500-QUADPAK | Set of 4 ZS1500 Active Probes | Optical to Electrical Converters
| | OE425 | Short wavelength O/E Converter (500-870 nm) | | OE455 | Long wavelength O/E Converter (950-1630 nm) | | OE525 | Short wavelength O/E Converter (500-870 nm) | | OE555 | Long wavelength O/E converter | Probe Adapters
| | LPA-SMA-A | Pro-Link to SMA Adapter, new style | | LPA-SMA-KIT-A | Kit of Pro-Link to SMA Adapter, new style | Probe Parts and Kits
| | Dx10-QC | Replacement Quick Connect lead set for D310/D610 | | Dx10-SI | Replacement Solder tip lead set for D310/D610 | | Dx10-SP | Replacement Square Pin lead set for D310/D610 | | Dx20-QC | Replacement Quick Connect lead set for D320/D620 | | Dx20-SI | Replacement Solder tip lead set for D320/D620 | | Dx20-SP | Replacement Square Pin lead set for D320/D620 |
|
|
|
