| |
|
WavePro 7Zi-Aシリーズ
WavePro 7Zi-Aシリーズは、特にデバッグと解析を最適化するためにまったく新しいフォームファクタとして、クラス最大のタッチスクリーン付き15インチ高分解能WXGA画面による高い操作性を実現していると同時に独自のリムーバブル･フロント･パネルにより、非測定回路の直近でオシロスコープを操作する新しい操作性も提供します。また、ロングメモリを使った信号捕捉で高度な解析を実施しても、
処理能力を大幅に強化し、ストレスなく多角的な解析を行うことが出来るようになりました。さらに新機能TriggerScanとWaveScan機能によりデバッグ/解析で大きな威力を発揮します。
- 1.5 〜 6 GHz帯域（帯域アップグレード可能）
- 標準メモリ：20Mポイント（4ch時）/40Mポイント（2ch時）
- 最大メモリ：128Mポイント（4ch時）/256Mポイント（2ch時）
- サンプリングレート：20GS/s（4ch時）/ 40GS/s（2ch時）
- 80ビットシリアル・パターン・トリガ（オプション、WavePro715Zi非対応）
高い汎用性
従来、4GHzを超える帯域のオシロスコープは、その帯域を確保することができる50Ω入力のみを備え、パッシブ･プローブなど汎用的なプローブの接続には、高インピーダンス変換アダプタの使用が必要となっていましたが、 WavePro 7Zi-Aシリーズでは高インピーダンス入力を標
準装備とし、また、ミックスド･シグナル・オプションに対応しているので、幅広いアプリケーションに簡単に対応で
きます。
帯域幅アップグレードが可能：1.5〜6GHz
すべてのWavePro 7Zi-Aシリーズのオシロスコープは、単一のハードウェア・プラットフ
ォームで設計されています。1.5〜6GHzの全帯域に渡ってアップグレードが最小のコス
トで可能です。
X-Stream II
ストリーミング･アーキテクチャ
X-Stream IIストリーミング･アーキテクチャでは、複数の100Mポイント波形(またはそれ以上の波形)を、オシロスコープで同時に処理するときでも、データ処理能力を高く
保つことを保証します。X-Stream IIでは、アクセス速度が速いCPUキャッシュメモリの使用効率を上げるために、波形データをキャッシュに合わせた可変長の波形セグメン
トに分割して処理することで、ボトルネックとなるメイン
メモリのアクセスを最小回数に抑えるので、計算速度が向上します。その結果、他のオシロスコープと比べて10〜100倍の処理速度が実現されます。
ロング･メモリ処理の最適化
X-Stream IIストリーミング･アーキテクチャでは、64ビットのオペレーティング･システムが広大なメモリ領域をリニアに扱えるので、
ロングメモリの波形データも制限なく取り扱うことが出来ます。
また、波形データをCPUキャッシュ・メモリに収まるサイズの可変長セグメントに分割できるため、解析の種類に関わらず、
実質的に解析メモリの長さに関する制限がありません。従来のアーキテクチャによる他のオシロスコープではこのような特性がサポートされず、
通常、最適な条件下でも解析メモリの長さは捕捉メモリの長さの5〜20%に制限されます。
応答性の最適化
WavePro 7Zi-Aシリーズでは、動的にバッファを割り当てることにより、演算処理の効率化を図ることで、フロント・パネルの応答性を最大化しています。また、フロント・パネルのコントロールの変更が行われると、実行中の処理が中断され、変更後の設定が即座に反映されます。また、波形のプレビューでは最終演算結果が表示されるまで、一時的に中間計算結果を表示し、スムーズな操作性を支援します。
ページトップへ
WaveScanTMの高度な検索／解析機能で検出可能
WaveScanには、異常イベント検出とソフトウェア・トリガ機能の両方が備わっています。
異常イベント検出ロングメモリを活かしてシングル・ショットで捕捉した波形の中の異常イベントを約30種類
(オプションでさらに増えます）の検索モードと検索条件を指定して検出することができます。検出された異常イベントが、
画面上にハイライト表示され、該当するイベントを一覧で確認できます。
一覧表示内のイベントをクリックすると、その箇所にジャンプします。
Trigger Scan
(異常波形を捕捉するプログラマブルトリガ)
あらかじめ設定したトリガ条件を自動的に切替えることにより、トリガ条件による波形スキャン機能を実現。これにより、異常波形データを高い確率で捕捉することがきる上に、その波形データそのものを解析することができます。
（ 参考資料
テク ニカルノートTrigger Scan）
外部転送用インタフェースに LSIB（PCI ExpressCable）を採用！
PCI Express Cableを外部転送インタフェースとして採用することにより、従来比で数十倍〜数百倍の250MB/secものデータ転送スピードを実現しました（LSIBオプションが必要）。これにより、高エネルギー物理関連の大規模実験施設や物理・化学関連の実験効率を飛躍的に高めることができます。
ページトップへ
リムーバブル・フロント・パネル 
オシロスコープから取り外して、測定作業の直近で操作が可能。また将来のカスタマイズにも対応予定。
 外部ディスプレイ（オプション）
外部ディスプレイを拡張デスクトップに設定して、特定のオシロスコープの機能を表示することができます。
ミックスド・シグナル・オプション(オプション)
接続するだけで最大36本・最高2GS/sのデジタル・チャンネルが追加され、ミックスド・シグナル・オシロスコープに変身。
（ MSシリーズ詳細ページへ）
各種解析オプション
各種コンプライアンステスト、ジッタ解析、スペクトラムアナライザ解析、統計解析、光ディスク解析など多種多様の解析オプションを追加することができます
低速バスオプション
CAN, LIN, FlexRayをはじめとする車載LANインタフェースをはじめ、I2C, SPI,UART等の汎用インタフェースのトリガ＆デコード機能を追加することができます（FlexRayTDPはEYEパターンによる物理層解析機能にも対応）。
ページトップへ
基本仕様
| モデル名 |
帯域 |
サンプリング速度(4ch時/2ch時) |
標準メモリ(4ch時/2ch時) |
| WavePro 715Zi-A |
1.5 GHz |
10/20 GS/s |
20/40 Mポイント |
| WavePro 725Zi-A |
2.5 GHz |
20/40 GS/s |
20/40 Mポイント |
| WavePro 735Zi-A |
3.5 GHz |
20/40 GS/s |
20/40 Mポイント |
| WavePro 740Zi-A |
4 GHz |
20/40 GS/s |
20/40 Mポイント |
| WavePro 760Zi-A |
6 GHz |
20/40 GS/s |
20/40 Mポイント |
モデルごとスペック詳細（モデル名をクリックで詳細表示されます）
 WavePro 715 Zi-A スペック
Vertical System
|
| Analog (ProBus Input) Bandwidth @ 50 Ω
(-3 dB) |
1.5 GHz (≥10 mV/div) |
| Analog (ProBus Input) Bandwidth @ 1 MΩ
(-3 dB) |
500 MHz (typical) (≥5 mV/div) |
| Rise Time (10–90%) |
235 ps (typical, flatness mode) |
| Rise Time (20–80%) |
176 ps (typical, flatness mode) |
| Input Channels |
4 |
| Bandwidth Limiters |
20 MHz, 200 MHz, 1 GHz |
| Input Impedance |
50 Ω+/-2% or 1 MΩ||16pF, 10 MΩ || 11 pF
with supplied Probe |
| Input Coupling |
ProBus Inputs - 1 MΩ: AC, DC, GND; 50
Ω: DC, GND |
| Maximum Input Voltage |
50 Ω: ±5 Vrms
1 MΩ: 250 V max. (peak AC: < 10 kHz + DC) |
| Channel-Channel Isolation |
DC to 2 GHz: 46 dB (>200:1 VSWR)
2 to 4 GHz: 34 dB (>50:1 VSWR)
4 to 6 GHz: 26 dB (>20:1 VSWR)
(For any two ProLink input channels, same v/div settings, typical) |
| Vertical Resolution |
8 bits; up to 11 bits with enhanced
resolution (ERES) |
| Sensitivity |
50 Ω: 2 mV–1 V/div, fully variable
(2-9.99 mV/div via zoom); 1 MΩ: 1 mV–10 V/div, fully variable |
| DC Gain Accuracy |
±1.5% of full scale |
| Offset Range |
50 Ω (ProBus):
±750 mV @ 10–170 mV/div
±4 V @ 172 mV/div -1 V/div
1 MΩ:
±1V @ 2–128 mV/div
±10V @ 130mV-1.28V/div
±100V @ 1.3V-10V/div |
| Offset Accuracy |
±(1.5% of full scale + 1.0% of offset
value + 1 mV) |
| |
Horizontal System
|
| Timebases |
Internal timebase common to 4 input
channels; an external clock may be applied at the auxiliary input |
| Time/Division Range |
20 ps/div–1000 s/div (RIS mode: 20 ps/div
- 10 ns/div; Roll mode: up to 1000 s/div) |
| Clock Accuracy |
< 1 ppm + (aging of 0.5ppm/yr from last
calibration) |
| Time Interval Accuracy |
< 0.06 / SR + (clock accuracy* Reading)
(rms) |
| Jitter Noise Floor |
1.5 ps (TIE, typical) |
| Trigger and Interpolator Jitter |
3 psrms (typical) <0.1 ps rms (typical,
software assisted) |
| Channel-Channel Deskew Range |
±9 x time/div. setting, 100 ms max.,
each channel |
| External Timebase Reference (Input) |
10 MHz; 50 Ω impedance, applied at the
rear input |
| External Timebase Reference (Output) |
10 MHz; 50 Ω impedance, output at the
rear |
| External Clock |
30 MHz–2 GHz, 50 Ω impedance, applied
at the auxiliary input |
| |
Acquisition System
|
| Single-Shot Sample Rate/Ch |
20 GS/s on 2 Ch
10 GS/s on 4 Ch
(Option WPZi-1.5GHZ-4X20GS doubles the sample rate) |
| Random Interleaved Sampling (RIS) |
200 GS/s for repetitive signals (20 ps/div
to 10 ns/div) |
| Maximum Trigger Rate |
1,000,000 waveforms/second (in Sequence
Mode, up to 4 channels) |
| Intersegment Time |
1 µs |
| Memory Options (4 Ch / 2 Ch / 1Ch) |
S-32 Option:
32M / 64M / 64M
(15,000)
M-64 Option:
64M / 128M / 128M
(15,000)
L-128 Option:
128M / 256M / 256M
(15,000) |
| Standard Memory (4 Ch / 2 Ch / 1Ch)
(Number of Segments) |
20M /40M / 40M
(5000) |
| |
Acquisition Processing
|
| Averaging |
Summed averaging to 1 million sweeps;
continuous averaging to 1 million sweeps |
| Enhanced Resolution (ERES) |
From 8.5 to 11 bits vertical resolution |
| Envelope (Extrema) |
Envelope, floor, or roof for up to 1
million sweeps |
| Interpolation |
Linear or Sin x/x |
| |
Triggering System
|
| Modes |
Normal, Auto, Single, and Stop |
| Sources |
Any input channel, Aux, Aux/10, or
line; slope and level unique to each source (except line trigger) |
| Coupling Mode |
DC, AC, HFRej, LFRej |
| Pre-trigger Delay |
0–100% of memory size (adjustable in 1%
increments of 100 ns) |
| Post-trigger Delay |
0–10,000 divisions in real time mode,
limited at slower time/div settings or in roll mode |
| Hold-off by Time |
From 2 ns up to 20 s or from 1 to
99,999,999 events |
| Internal Trigger Range |
±4.1 div from center |
| Trigger Sensitivity with Edge Trigger
(Ch 1–4) ProBus Inputs |
2 div @ < 1.5 GHz
1.5 div @ < 750 MHz
1.0 div @ < 200 MHz
(for DC, AC, LFRej coupling, ≥ 10 mV/div, 50 Ω ) |
| External Trigger Sensitivity, (Edge
Trigger) |
2 div @ < 1 GHz
1.5 div @ < 500 MHz
1.0 div @ < 200 MHz
(for DC, AC, LFRej coupling) |
| External Trigger Input Range |
Aux (±0.4 V); Aux/10 (±4 V) |
| Max. Trigger Frequency, SMART Trigger
|
1.5 GHz @ ≥ 10 mV/div (minimum
triggerable width 500 ps) |
| |
Basic Triggers
|
| Edge |
Triggers when signal meets slope
(positive, negative, or either) and level condition. |
| Window |
Triggers when signal exits a window
defined by adjustable thresholds |
| TV-Composite Video |
Triggers NTSC or PAL with selectable
line and field; HDTV (720p, 1080i, 1080p) with selectable frame rate
(50 or 60 Hz) and Line; or CUSTOM with selectable Fields (1-8),
Lines (up to 2000), Frame Rates (25, 30, 50, or 60 Hz), Interlacing
(1:1, 2:1, 4:1, 8 |
| |
SMART Triggers
|
| State or Edge Qualified |
Triggers on any input source only if a
defined state or edge occurred on another input source. Delay
between sources is selectable by time or events. |
| Qualified First |
In Sequence acquisition mode, triggers
repeatably on event B only if a defined pattern, state, or edge
(event A) is satisfied in the first segment of the acquisition.
Holdoff between sources is selectable by time or events. |
| Dropout |
Triggers if signal drops out for longer
than selected time between 1 ns and 20 s. |
| Pattern |
Logic combination (AND, NAND, OR, NOR)
of 5 inputs (4 channels and external trigger input). Each source can
be high, low, or don’t care. The High and Low level can be selected
independently. Triggers at start or end of the pattern. |
| |
SMART Triggers with Exclusion Technology
|
| Glitch |
Triggers on positive or negative
glitches with widths selectable as low as 200ps (depending on
oscilloscope bandwidth) to 20 s, or on intermittent faults. |
| Width (Signal or Pattern) |
Triggers on positive, negative, or both
widths with widths selectable as low as 200ps (depending on
oscilloscope bandwidth) to 20 s, or on intermittent faults. |
| Interval (Signal or Pattern) |
Triggers on intervals selectable
between 1 ns and 20 s. |
| Timeout (State/Edge Qualified) |
Triggers on any source if a given state
(or transition edge) has occurred on another source. Delay between
sources is 1 ns to 20 s, or 1 to 99,999,999 events. |
| Runt |
Trigger on positive or negative runts
defined by two voltage limits and two time limits. Select between 1
ns and 20 ns. |
| Slew Rate |
Trigger on edge rates. Select limits
for dV, dt, and slope. Select edge limits between 1 ns and 20 ns. |
| Exclusion Triggering |
Trigger on intermittent faults by
specifying the expected behavior and triggering when that condition
is not met |
| |
Cascade (Sequence) Triggering
|
| Capability |
Arm on "A" event, then Trigger on "B"
event. Or Arm on "A" event, then Qualify on "B" event, and Trigger
on "C" event. Or Arm on “A” event, then Qualify on “B” then “C”
event, and Trigger on “D” event |
| Types |
A, B, C, or D event: Edge, Glitch,
Width, Window, Dropout, Interval, Runt, Slew Rate, or Pattern
(analog). |
| Holdoff |
Holdoff between A and B, B and C, C or
D, or any is selectable by time or number of events |
| Reset |
Reset between A and B, B and C, C and
D, or any combination is selectable in time or number of events |
| |
High Speed Serial Protocol Triggering
|
| Pattern Length |
- |
| Clock and Data Outputs |
- |
| Clock Recovery Jitter |
- |
| Hardware Clock Recovery Loop BW |
- |
| |
Color Waveform Display
|
| Type |
Color 15.3" flat panel TFT-Active
Matrix LCD with high resolution touch screen |
| Resolution |
WXGA; 1280 x 768 pixels. |
| Number of traces |
Display a maximum of 8 traces.
Simultaneously display channel, zoom, memory and math traces. |
| Grid Styles |
Auto, Single, Dual, Quad, Octal, X-Y,
Single+X-Y, Dual+X-Y |
| Waveform Representation |
Sample dots joined, or sample dots only |
| |
Processor/CPU
|
| Type |
Intel® CoreTM 2 Quad, 3 GHz (or better) |
| Processor Memory |
8 GB standard |
| Operating System |
Microsoft Windows® Vista Business
Edition (64-bit) with SP1 |
| Real Time Clock |
Date and time displayed with waveform
in hardcopy files. SNTP support to synchronize to precision internal
clocks. |
| |
Setup Storage
|
| Front Panel and Instrument Status |
Store to the internal hard drive, over
the network, or to a USB-connected peripheral device. |
| |
Interface
|
| Remote Control |
Via Windows Automation, or via LeCroy
Remote Command Set |
| Network Communication Standard |
VXI-11 or VICP, LXI Class C (v 1.2)
Compliant |
| GPIB Port (optional) |
Supports IEEE – 488.2 |
| LSIB Port (optional) |
Supports PCIe Gen1 x4 protocol with
LeCroy supplied API |
| Ethernet Port |
Supports 10/100/1000BaseT Ethernet
interface (RJ45 port) |
| USB Ports |
minimum 6 total (incl. 3 front panel)
USB 2.0 ports support Windows compatible devices |
| External Monitor Port |
15 pin D-Type WXGA compatible to
support customer-supplied external monitor. DVI and power connector
to support LeCroy WPZi-EXTDISP-15 additional touch screen display
accessory. Includes support for extended desktop operation with
optional LeCroy or other |
| Peripheral Bus |
LeCroy LBUS standard |
| |
Auxiliary Output
|
| Connector Type |
BNC, located on front |
| Signal Types |
Select from calibrator, control signals
or Off |
| Output Signal |
500 Hz–5 MHz square wave or DC level;
2.5mV to 500 mV into 50 Ω (5 mV–1 V into 1 MΩ) |
| Control Signals |
Trigger enabled, trigger out, pass/fail
status, off |
| |
Power Requirements
|
| Voltage |
100–240 VAC ±10% at 45-66 Hz; 100-120
VAC ±10% at 380-420 Hz; Automatic AC Voltage Selection; |
| Max. Power Consumption |
850 W/850 VA |
| |
Environmental and Safety
|
| Temperature (Operating) |
+5 °C to +40 °C including CD-RW/DVD-ROM
drive |
| Temperature (Non-Operating) |
–20 °C to +60 °C |
| Humidity (Operating) |
5% to 80% relative humidity
(non-condensing) up to +31 °C. Upper limit derates to 50% relative
humidity (non-condensing) at +40 °C. |
| Humidity (Non-Operating) |
5% to 95% relative humidity
(non-condensing) as tested per MIL-PRF-28800F |
| Altitude (Operating) |
Up to 10,000 ft. (3048 m) at or below
+25 °C |
| Altitude (Non-Operating) |
Up to 40,000 ft. (12,192 m) |
| Random Vibration (Operating) |
0.5 grms 5 Hz to 500 Hz, 10 minutes in
each of three orthogonal axes, 30 minutes total |
| Random Vibration (Non-Operating) |
2.0 grms 5 Hz to 500 Hz, 10 minutes in
each of three orthogonal axes, 30 minutes total |
| Functional Shock |
20 g peak, half sine, 11 ms pulse, 3
shocks (positive and negative) in each of three orthogonal axes, 18
shocks total |
| |
Physical Dimensions
|
| Dimensions (HWD) |
14"H x 18.4"W x 11.4"D (355 x 467 x 289
mm) |
| Weight |
40.5 lbs. (18.4 kg) |
| Shipping Weight |
62 lbs. (28.2 kg) |
| |
Certifications
|
| Certifications |
CE Compliant, UL and cUL listed;
conforms to EN 61326-1, EN 61010-1, UL 61010-1 2nd edition, and CSA
C22.2 No. 61010-1-04 |
| |
Warranty and Service
|
| Warranty and Service |
3-year warranty; calibration
recommended annually. Optional service programs include extended
warranty, upgrades, and calibration services. |
| |
WavePro 725 Zi-A スペック
Vertical System
|
| Analog (ProBus Input) Bandwidth @ 50 Ω
(-3 dB) |
2.5 GHz (≥10 mV/div) |
| Analog (ProBus Input) Bandwidth @ 1 MΩ
(-3 dB) |
500 MHz (typical) (≥5 mV/div) |
| Rise Time (10–90%) |
150 ps (typical, flatness mode) |
| Rise Time (20–80%) |
113 ps (typical, flatness mode) |
| Input Channels |
4 |
| Bandwidth Limiters |
20 MHz, 200 MHz, 1 GHz |
| Input Impedance |
50 Ω+/-2% or 1 MΩ||16pF, 10 MΩ || 11 pF
with supplied Probe |
| Input Coupling |
ProBus Inputs - 1 MΩ: AC, DC, GND; 50
Ω: DC, GND |
| Maximum Input Voltage |
50 Ω: ±5 Vrms
1 MΩ: 250 V max. (peak AC: < 10 kHz + DC) |
| Channel-Channel Isolation |
DC to 2 GHz: 46 dB (>200:1 VSWR)
2 to 4 GHz: 34 dB (>50:1 VSWR)
4 to 6 GHz: 26 dB (>20:1 VSWR)
(For any two ProLink input channels, same v/div settings, typical) |
| Vertical Resolution |
8 bits; up to 11 bits with enhanced
resolution (ERES) |
| Sensitivity |
50 Ω: 2 mV–1 V/div, fully variable
(2-9.99 mV/div via zoom); 1 MΩ: 1 mV–10 V/div, fully variable |
| DC Gain Accuracy |
±1.5% of full scale |
| Offset Range |
50 Ω (ProBus):
±750 mV @ 10–170 mV/div
±4 V @ 172 mV/div -1 V/div
1 MΩ:
±1V @ 2–128 mV/div
±10V @ 130mV-1.28V/div
±100V @ 1.3V-10V/div |
| Offset Accuracy |
±(1.5% of full scale + 1.0% of offset
value + 1 mV) |
| |
Horizontal System
|
| Timebases |
Internal timebase common to 4 input
channels; an external clock may be applied at the auxiliary input |
| Time/Division Range |
20 ps/div–1000 s/div (RIS mode: 20 ps/div
- 10 ns/div; Roll mode: up to 1000 s/div) |
| Clock Accuracy |
< 1 ppm + (aging of 0.5ppm/yr from last
calibration) |
| Time Interval Accuracy |
< 0.06 / SR + (clock accuracy* Reading)
(rms) |
| Jitter Noise Floor |
1.0 ps (TIE, typical) |
| Trigger and Interpolator Jitter |
2 psrms (typical) <0.1 ps rms (typical,
software assisted) |
| Channel-Channel Deskew Range |
±9 x time/div. setting, 100 ms max.,
each channel |
| External Timebase Reference (Input) |
10 MHz; 50 Ω impedance, applied at the
rear input |
| External Timebase Reference (Output) |
10 MHz; 50 Ω impedance, output at the
rear |
| External Clock |
30 MHz–2 GHz, 50 Ω impedance, applied
at the auxiliary input |
| |
Acquisition System
|
| Single-Shot Sample Rate/Ch |
40 GS/s on 2 Ch
20 GS/s on 4 Ch |
| Random Interleaved Sampling (RIS) |
200 GS/s for repetitive signals (20 ps/div
to 10 ns/div) |
| Maximum Trigger Rate |
1,000,000 waveforms/second (in Sequence
Mode, up to 4 channels) |
| Intersegment Time |
1 µs |
| Memory Options (4 Ch / 2 Ch / 1Ch) |
S-32 Option:
32M / 64M / 64M
(15,000)
M-64 Option:
64M / 128M / 128M
(15,000)
L-128 Option:
128M / 256M / 256M
(15,000) |
| Standard Memory (4 Ch / 2 Ch / 1Ch)
(Number of Segments) |
20 M / 40 M / 40M
(5000) |
| |
Acquisition Processing
|
| Averaging |
Summed averaging to 1 million sweeps;
continuous averaging to 1 million sweeps |
| Enhanced Resolution (ERES) |
From 8.5 to 11 bits vertical resolution |
| Envelope (Extrema) |
Envelope, floor, or roof for up to 1
million sweeps |
| Interpolation |
Linear or Sin x/x |
| |
Triggering System
|
| Modes |
Normal, Auto, Single, and Stop |
| Sources |
Any input channel, Aux, Aux/10, or
line; slope and level unique to each source (except line trigger) |
| Coupling Mode |
DC, AC, HFRej, LFRej |
| Pre-trigger Delay |
0–100% of memory size (adjustable in 1%
increments of 100 ns) |
| Post-trigger Delay |
0–10,000 divisions in real time mode,
limited at slower time/div settings or in roll mode |
| Hold-off by Time |
From 2 ns up to 20 s or from 1 to
99,999,999 events |
| Internal Trigger Range |
±4.1 div from center |
| Trigger Sensitivity with Edge Trigger
(Ch 1–4) ProBus Inputs |
2 div @ < 2.5 GHz
1.5 div @ < 1.25 GHz
1.0 div @ < 200 MHz
(for DC, AC, LFRej coupling, ≥ 10 mV/div, 50 Ω ) |
| External Trigger Sensitivity, (Edge
Trigger) |
2 div @ < 1 GHz
1.5 div @ < 500 MHz
1.0 div @ < 200 MHz
(for DC, AC, LFRej coupling) |
| External Trigger Input Range |
Aux (±0.4 V); Aux/10 (±4 V) |
| Max. Trigger Frequency, SMART Trigger
|
2.0 GHz @ ≥ 10 mV/div (minimum
triggerable width 300 ps) |
| |
Basic Triggers
|
| Edge |
Triggers when signal meets slope
(positive, negative, or either) and level condition. |
| Window |
Triggers when signal exits a window
defined by adjustable thresholds |
| TV-Composite Video |
Triggers NTSC or PAL with selectable
line and field; HDTV (720p, 1080i, 1080p) with selectable frame rate
(50 or 60 Hz) and Line; or CUSTOM with selectable Fields (1-8),
Lines (up to 2000), Frame Rates (25, 30, 50, or 60 Hz), Interlacing
(1:1, 2:1, 4:1, 8 |
| |
SMART Triggers
|
| State or Edge Qualified |
Triggers on any input source only if a
defined state or edge occurred on another input source. Delay
between sources is selectable by time or events. |
| Qualified First |
In Sequence acquisition mode, triggers
repeatably on event B only if a defined pattern, state, or edge
(event A) is satisfied in the first segment of the acquisition.
Holdoff between sources is selectable by time or events. |
| Dropout |
Triggers if signal drops out for longer
than selected time between 1 ns and 20 s. |
| Pattern |
Logic combination (AND, NAND, OR, NOR)
of 5 inputs (4 channels and external trigger input). Each source can
be high, low, or don’t care. The High and Low level can be selected
independently. Triggers at start or end of the pattern. |
| |
SMART Triggers with Exclusion Technology
|
| Glitch |
Triggers on positive or negative
glitches with widths selectable as low as 200ps (depending on
oscilloscope bandwidth) to 20 s, or on intermittent faults. |
| Width (Signal or Pattern) |
Triggers on positive, negative, or both
widths with widths selectable as low as 200ps (depending on
oscilloscope bandwidth) to 20 s, or on intermittent faults. |
| Interval (Signal or Pattern) |
Triggers on intervals selectable
between 1 ns and 20 s. |
| Timeout (State/Edge Qualified) |
Triggers on any source if a given state
(or transition edge) has occurred on another source. Delay between
sources is 1 ns to 20 s, or 1 to 99,999,999 events. |
| Runt |
Trigger on positive or negative runts
defined by two voltage limits and two time limits. Select between 1
ns and 20 ns. |
| Slew Rate |
Trigger on edge rates. Select limits
for dV, dt, and slope. Select edge limits between 1 ns and 20 ns. |
| Exclusion Triggering |
Trigger on intermittent faults by
specifying the expected behavior and triggering when that condition
is not met |
| |
Cascade (Sequence) Triggering
|
| Capability |
Arm on "A" event, then Trigger on "B"
event. Or Arm on "A" event, then Qualify on "B" event, and Trigger
on "C" event. Or Arm on “A” event, then Qualify on “B” then “C”
event, and Trigger on “D” event |
| Types |
A, B, C, or D event: Edge, Glitch,
Width, Window, Dropout, Interval, Runt, Slew Rate, or Pattern
(analog). |
| Holdoff |
Holdoff between A and B, B and C, C or
D, or any is selectable by time or number of events |
| Reset |
Reset between A and B, B and C, C and
D, or any combination is selectable in time or number of events |
| |
High Speed Serial Protocol Triggering
|
| Data Rates |
(Option WPZi-MSPT) 100 Mb/s - 1.25 Gb/s |
| Pattern Length |
80 bits, NRZ or 8b10b |
| Clock and Data Outputs |
400mVp-p (typical) AC coupled |
| Clock Recovery Jitter |
1 ps rms + 0.3% Unit Interval rms for
PRBS data patterns with 50% transition density |
| Hardware Clock Recovery Loop BW |
PLL Loop BW = Fbaud/5500, 100 Mb/s to
2.488 Gb/s (typical) |
| |
Color Waveform Display
|
| Type |
Color 15.3" flat panel TFT-Active
Matrix LCD with high resolution touch screen |
| Resolution |
WXGA; 1280 x 768 pixels. |
| Number of traces |
Display a maximum of 8 traces.
Simultaneously display channel, zoom, memory and math traces. |
| Grid Styles |
Auto, Single, Dual, Quad, Octal, X-Y,
Single+X-Y, Dual+X-Y |
| Waveform Representation |
Sample dots joined, or sample dots only |
| |
Processor/CPU
|
| Type |
Intel® CoreTM 2 Quad, 3 GHz (or better) |
| Processor Memory |
8 GB standard |
| Operating System |
Microsoft Windows® Vista Business
Edition (64-bit) with SP1 |
| Real Time Clock |
Date and time displayed with waveform
in hardcopy files. SNTP support to synchronize to precision internal
clocks. |
| |
Setup Storage
|
| Front Panel and Instrument Status |
Store to the internal hard drive, over
the network, or to a USB-connected peripheral device. |
| |
Interface
|
| Remote Control |
Via Windows Automation, or via LeCroy
Remote Command Set |
| Network Communication Standard |
VXI-11 or VICP, LXI Class C (v 1.2)
Compliant |
| GPIB Port (optional) |
Supports IEEE – 488.2 |
| LSIB Port (optional) |
Supports PCIe Gen1 x4 protocol with
LeCroy supplied API |
| Ethernet Port |
Supports 10/100/1000BaseT Ethernet
interface (RJ45 port) |
| USB Ports |
minimum 6 total (incl. 3 front panel)
USB 2.0 ports support Windows compatible devices |
| External Monitor Port |
15 pin D-Type WXGA compatible to
support customer-supplied external monitor. DVI and power connector
to support LeCroy WPZi-EXTDISP-15 additional touch screen display
accessory. Includes support for extended desktop operation with
optional LeCroy or other |
| Peripheral Bus |
LeCroy LBUS standard |
| |
Auxiliary Output
|
| Connector Type |
BNC, located on front |
| Signal Types |
Select from calibrator, control signals
or Off |
| Output Signal |
500 Hz–5 MHz square wave or DC level;
2.5mV to 500 mV into 50 Ω (5 mV–1 V into 1 MΩ) |
| Control Signals |
Trigger enabled, trigger out, pass/fail
status, off |
| |
Power Requirements
|
| Voltage |
100–240 VAC ±10% at 45-66 Hz; 100-120
VAC ±10% at 380-420 Hz; Automatic AC Voltage Selection; |
| Max. Power Consumption |
850 W/850 VA |
| |
Environmental and Safety
|
| Temperature (Operating) |
+5 °C to +40 °C including CD-RW/DVD-ROM
drive |
| Temperature (Non-Operating) |
–20 °C to +60 °C |
| Humidity (Operating) |
5% to 80% relative humidity
(non-condensing) up to +31 °C. Upper limit derates to 50% relative
humidity (non-condensing) at +40 °C. |
| Humidity (Non-Operating) |
5% to 95% relative humidity
(non-condensing) as tested per MIL-PRF-28800F |
| Altitude (Operating) |
Up to 10,000 ft. (3048 m) at or below
+25 °C |
| Altitude (Non-Operating) |
Up to 40,000 ft. (12,192 m) |
| Random Vibration (Operating) |
0.5 grms 5 Hz to 500 Hz, 10 minutes in
each of three orthogonal axes, 30 minutes total |
| Random Vibration (Non-Operating) |
2.0 grms 5 Hz to 500 Hz, 10 minutes in
each of three orthogonal axes, 30 minutes total |
| Functional Shock |
20 g peak, half sine, 11 ms pulse, 3
shocks (positive and negative) in each of three orthogonal axes, 18
shocks total |
| |
Physical Dimensions
|
| Dimensions (HWD) |
14"H x 18.4"W x 11.4"D (355 x 467 x 289
mm) |
| Weight |
40.5 lbs. (18.4 kg) |
| Shipping Weight |
62 lbs. (28.2 kg) |
| |
Certifications
|
| Certifications |
CE Compliant, UL and cUL listed;
conforms to EN 61326-1, EN 61010-1, UL 61010-1 2nd edition, and CSA
C22.2 No. 61010-1-04 |
| |
Warranty and Service
|
| Warranty and Service |
3-year warranty; calibration
recommended annually. Optional service programs include extended
warranty, upgrades, and calibration services. |
| |
WavePro 735 Zi-A スペック
Vertical System
|
| Analog (ProBus Input) Bandwidth @ 50
Ω (-3 dB) |
3.5 GHz (≥10 mV/div) |
| Analog (ProBus Input) Bandwidth @ 1
MΩ (-3 dB) |
500 MHz (typical) (≥5 mV/div) |
| Rise Time (10–90%) |
120ps (typical, flatness mode) |
| Rise Time (20–80%) |
90ps (typical, flatness mode) |
| Input Channels |
4 |
| Bandwidth Limiters |
20 MHz, 200 MHz, 1 GHz, 3 GHz |
| Input Impedance |
50 Ω+/-2% or 1 MΩ||16pF, 10 MΩ || 11
pF with supplied Probe |
| Input Coupling |
ProBus Inputs - 1 MΩ: AC, DC, GND; 50
Ω: DC, GND |
| Maximum Input Voltage |
50 Ω: ±5 Vrms
1 MΩ: 250 V max. (peak AC: < 10 kHz + DC) |
| Channel-Channel Isolation |
DC to 2 GHz: 46 dB (>200:1 VSWR)
2 to 4 GHz: 34 dB (>50:1 VSWR)
4 to 6 GHz: 26 dB (>20:1 VSWR)
(For any two ProLink input channels, same v/div settings, typical) |
| Vertical Resolution |
8 bits; up to 11 bits with enhanced
resolution (ERES) |
| Sensitivity |
50 Ω: 2 mV–1 V/div, fully variable
(2-9.99 mV/div via zoom); 1 MΩ: 1 mV–10 V/div, fully variable |
| DC Gain Accuracy |
±1.5% of full scale |
| Offset Range |
50 Ω (ProBus):
±750 mV @ 10–170 mV/div
±4 V @ 172 mV/div -1 V/div
1 MΩ:
±1V @ 2–128 mV/div
±10V @ 130mV-1.28V/div
±100V @ 1.3V-10V/div |
| Offset Accuracy |
±(1.5% of full scale + 1.0% of offset
value + 1 mV) |
| |
Horizontal System
|
| Timebases |
Internal timebase common to 4 input
channels; an external clock may be applied at the auxiliary input |
| Time/Division Range |
20 ps/div–1000 s/div (RIS mode: 20 ps/div
- 10 ns/div; Roll mode: up to 1000 s/div) |
| Clock Accuracy |
< 1 ppm + (aging of 0.5ppm/yr from
last calibration) |
| Time Interval Accuracy |
< 0.06 / SR + (clock accuracy*
Reading) (rms) |
| Jitter Noise Floor |
800 fs (TIE, typical) |
| Trigger and Interpolator Jitter |
2 psrms (typical) <0.1 ps rms
(typical, software assisted) |
| Channel-Channel Deskew Range |
±9 x time/div. setting, 100 ms max.,
each channel |
| External Timebase Reference (Input) |
10 MHz; 50 Ω impedance, applied at
the rear input |
| External Timebase Reference (Output) |
10 MHz; 50 Ω impedance, output at the
rear |
| External Clock |
30 MHz–2 GHz, 50 Ω impedance, applied
at the auxiliary input |
| |
Acquisition System
|
| Single-Shot Sample Rate/Ch |
40 GS/s on 2 Ch
20 GS/s on 4 Ch |
| Random Interleaved Sampling (RIS) |
200 GS/s for repetitive signals (20
ps/div to 10 ns/div) |
| Maximum Trigger Rate |
1,000,000 waveforms/second (in
Sequence Mode, up to 4 channels) |
| Intersegment Time |
1 µs |
| Memory Options (4 Ch / 2 Ch / 1Ch) |
S-32 Option:
32M / 64M / 64M
(15,000)
M-64 Option:
64M / 128M / 128M
(15,000)
L-128 Option:
128M / 256M / 256M
(15,000) |
| Standard Memory (4 Ch / 2 Ch / 1Ch)
(Number of Segments) |
20 M / 40 M / 40M
(5000) |
| |
Acquisition Processing
|
| Averaging |
Summed averaging to 1 million sweeps;
continuous averaging to 1 million sweeps |
| Enhanced Resolution (ERES) |
From 8.5 to 11 bits vertical
resolution |
| Envelope (Extrema) |
Envelope, floor, or roof for up to 1
million sweeps |
| Interpolation |
Linear or Sin x/x |
| |
Triggering System
|
| Modes |
Normal, Auto, Single, and Stop |
| Sources |
Any input channel, Aux, Aux/10, or
line; slope and level unique to each source (except line trigger) |
| Coupling Mode |
DC, AC, HFRej, LFRej |
| Pre-trigger Delay |
0–100% of memory size (adjustable in
1% increments of 100 ns) |
| Post-trigger Delay |
0–10,000 divisions in real time mode,
limited at slower time/div settings or in roll mode |
| Hold-off by Time |
From 2 ns up to 20 s or from 1 to
99,999,999 events |
| Internal Trigger Range |
±4.1 div from center |
| Trigger Sensitivity with Edge Trigger
(Ch 1–4) ProBus Inputs |
2 div @ < 3.5 GHz
1.5 div @ < 1.75 GHz
1.0 div @ < 200 MHz
(for DC, AC, LFRej coupling, ≥ 10 mV/div, 50 Ω ) |
| External Trigger Sensitivity, (Edge
Trigger) |
2 div @ < 1 GHz
1.5 div @ < 500 MHz
1.0 div @ < 200 MHz
(for DC, AC, LFRej coupling) |
| External Trigger Input Range |
Aux (±0.4 V); Aux/10 (±4 V) |
| Max. Trigger Frequency, SMART Trigger
|
2.0 GHz @ ≥ 10 mV/div (minimum
triggerable width 250 ps) |
| |
Basic Triggers
|
| Edge |
Triggers when signal meets slope
(positive, negative, or either) and level condition. |
| Window |
Triggers when signal exits a window
defined by adjustable thresholds |
| TV-Composite Video |
Triggers NTSC or PAL with selectable
line and field; HDTV (720p, 1080i, 1080p) with selectable frame
rate (50 or 60 Hz) and Line; or CUSTOM with selectable Fields
(1-8), Lines (up to 2000), Frame Rates (25, 30, 50, or 60 Hz),
Interlacing (1:1, 2:1, 4:1, 8 |
| |
SMART Triggers
|
| State or Edge Qualified |
Triggers on any input source only if
a defined state or edge occurred on another input source. Delay
between sources is selectable by time or events. |
| Qualified First |
In Sequence acquisition mode,
triggers repeatably on event B only if a defined pattern, state,
or edge (event A) is satisfied in the first segment of the
acquisition. Holdoff between sources is selectable by time or
events. |
| Dropout |
Triggers if signal drops out for
longer than selected time between 1 ns and 20 s. |
| Pattern |
Logic combination (AND, NAND, OR,
NOR) of 5 inputs (4 channels and external trigger input). Each
source can be high, low, or don’t care. The High and Low level can
be selected independently. Triggers at start or end of the
pattern. |
| |
SMART Triggers with Exclusion Technology
|
| Glitch |
Triggers on positive or negative
glitches with widths selectable as low as 200ps (depending on
oscilloscope bandwidth) to 20 s, or on intermittent faults. |
| Width (Signal or Pattern) |
Triggers on positive, negative, or
both widths with widths selectable as low as 200ps (depending on
oscilloscope bandwidth) to 20 s, or on intermittent faults. |
| Interval (Signal or Pattern) |
Triggers on intervals selectable
between 1 ns and 20 s. |
| Timeout (State/Edge Qualified) |
Triggers on any source if a given
state (or transition edge) has occurred on another source. Delay
between sources is 1 ns to 20 s, or 1 to 99,999,999 events. |
| Runt |
Trigger on positive or negative runts
defined by two voltage limits and two time limits. Select between
1 ns and 20 ns. |
| Slew Rate |
Trigger on edge rates. Select limits
for dV, dt, and slope. Select edge limits between 1 ns and 20 ns. |
| Exclusion Triggering |
Trigger on intermittent faults by
specifying the expected behavior and triggering when that
condition is not met |
| |
Cascade (Sequence) Triggering
|
| Capability |
Arm on "A" event, then Trigger on "B"
event. Or Arm on "A" event, then Qualify on "B" event, and Trigger
on "C" event. Or Arm on “A” event, then Qualify on “B” then “C”
event, and Trigger on “D” event |
| Types |
A, B, C, or D event: Edge, Glitch,
Width, Window, Dropout, Interval, Runt, Slew Rate, or Pattern
(analog). |
| Holdoff |
Holdoff between A and B, B and C, C
or D, or any is selectable by time or number of events |
| Reset |
Reset between A and B, B and C, C and
D, or any combination is selectable in time or number of events |
| |
High Speed Serial Protocol Triggering
|
| Data Rates |
(Option WPZi-MSPT) 100 Mb/s - 1.25 Gb/s |
| Pattern Length |
80 bits, NRZ or 8b10b |
| Clock and Data Outputs |
400mVp-p (typical) AC coupled |
| Clock Recovery Jitter |
1 ps rms + 0.3% Unit Interval rms for
PRBS data patterns with 50% transition density |
| Hardware Clock Recovery Loop BW |
PLL Loop BW = Fbaud/5500, 100 Mb/s to
2.488 Gb/s (typical) |
| |
Color Waveform Display
|
| Type |
Color 15.3" flat panel TFT-Active
Matrix LCD with high resolution touch screen |
| Resolution |
WXGA; 1280 x 768 pixels. |
| Number of traces |
Display a maximum of 8 traces.
Simultaneously display channel, zoom, memory and math traces. |
| Grid Styles |
Auto, Single, Dual, Quad, Octal, X-Y,
Single+X-Y, Dual+X-Y |
| Waveform Representation |
Sample dots joined, or sample dots
only |
| |
Processor/CPU
|
| Type |
Intel® CoreTM 2 Quad, 3 GHz (or
better) |
| Processor Memory |
8 GB standard |
| Operating System |
Microsoft Windows® Vista Business
Edition (64-bit) with SP1 |
| Real Time Clock |
Date and time displayed with waveform
in hardcopy files. SNTP support to synchronize to precision
internal clocks. |
| |
Setup Storage
|
| Front Panel and Instrument Status |
Store to the internal hard drive,
over the network, or to a USB-connected peripheral device. |
| |
Interface
|
| Remote Control |
Via Windows Automation, or via LeCroy
Remote Command Set |
| Network Communication Standard |
VXI-11 or VICP, LXI Class C (v 1.2)
Compliant |
| GPIB Port (optional) |
Supports IEEE – 488.2 |
| LSIB Port (optional) |
Supports PCIe Gen1 x4 protocol with
LeCroy supplied API |
| Ethernet Port |
Supports 10/100/1000BaseT Ethernet
interface (RJ45 port) |
| USB Ports |
minimum 6 total (incl. 3 front panel)
USB 2.0 ports support Windows compatible devices |
| External Monitor Port |
15 pin D-Type WXGA compatible to
support customer-supplied external monitor. DVI and power
connector to support LeCroy WPZi-EXTDISP-15 additional touch
screen display accessory. Includes support for extended desktop
operation with optional LeCroy or other |
| Peripheral Bus |
LeCroy LBUS standard |
| |
Auxiliary Output
|
| Connector Type |
BNC, located on front |
| Signal Types |
Select from calibrator, control
signals or Off |
| Output Signal |
500 Hz–5 MHz square wave or DC level;
2.5mV to 500 mV into 50 Ω (5 mV–1 V into 1 MΩ) |
| Control Signals |
Trigger enabled, trigger out,
pass/fail status, off |
| |
Power Requirements
|
| Voltage |
100–240 VAC ±10% at 45-66 Hz; 100-120
VAC ±10% at 380-420 Hz; Automatic AC Voltage Selection; |
| Max. Power Consumption |
850 W/850 VA |
| |
Environmental and Safety
|
| Temperature (Operating) |
+5 °C to +40 °C including
CD-RW/DVD-ROM drive |
| Temperature (Non-Operating) |
–20 °C to +60 °C |
| Humidity (Operating) |
5% to 80% relative humidity
(non-condensing) up to +31 °C. Upper limit derates to 50% relative
humidity (non-condensing) at +40 °C. |
| Humidity (Non-Operating) |
5% to 95% relative humidity
(non-condensing) as tested per MIL-PRF-28800F |
| Altitude (Operating) |
Up to 10,000 ft. (3048 m) at or below
+25 °C |
| Altitude (Non-Operating) |
Up to 40,000 ft. (12,192 m) |
| Random Vibration (Operating) |
0.5 grms 5 Hz to 500 Hz, 10 minutes
in each of three orthogonal axes, 30 minutes total |
| Random Vibration (Non-Operating) |
2.0 grms 5 Hz to 500 Hz, 10 minutes
in each of three orthogonal axes, 30 minutes total |
| Functional Shock |
20 g peak, half sine, 11 ms pulse, 3
shocks (positive and negative) in each of three orthogonal axes,
18 shocks total |
| |
Physical Dimensions
|
| Dimensions (HWD) |
14"H x 18.4"W x 11.4"D (355 x 467 x
289 mm) |
| Weight |
40.5 lbs. (18.4 kg) |
| Shipping Weight |
62 lbs. (28.2 kg) |
| |
Certifications
|
| Certifications |
CE Compliant, UL and cUL listed;
conforms to EN 61326-1, EN 61010-1, UL 61010-1 2nd edition, and
CSA C22.2 No. 61010-1-04 |
| |
Warranty and Service
|
| Warranty and Service |
3-year warranty; calibration
recommended annually. Optional service programs include extended
warranty, upgrades, and calibration services. |
| |
WavePro 740-A Zi スペック
Vertical System
|
| Analog (ProLink Input) Bandwidth @ 50
Ω (-3 dB) |
4 GHz (≥10 mV/div) |
| Analog (ProBus Input) Bandwidth @ 50
Ω (-3 dB) |
3.5 GHz (≥10 mV/div) |
| Analog (ProBus Input) Bandwidth @ 1
MΩ (-3 dB) |
500 MHz (typical) (≥5 mV/div) |
| Rise Time (10–90%) |
105 ps (typical, flatness mode) |
| Rise Time (20–80%) |
79 ps (typical, flatness mode) |
| Input Channels |
4 |
| Bandwidth Limiters |
20 MHz, 200 MHz, 1 GHz, 3 GHz |
| Input Impedance |
50 Ω+/-2% or 1 MΩ||16pF, 10 MΩ || 11
pF with supplied Probe |
| Input Coupling |
ProLink Inputs - 50 Ω: DC, GND
ProBus Inputs - 1 MΩ: AC, DC, GND; 50 Ω: DC, GND |
| Maximum Input Voltage |
50 Ω (ProBus): ±5 Vrms
50 Ω (ProLink): ±4 Vpeak
1 MΩ (ProBus): 250 V max. (peak AC: < 10 kHz + DC) |
| Channel-Channel Isolation |
DC to 2 GHz: 46 dB (>200:1 VSWR)
2 to 4 GHz: 34 dB (>50:1 VSWR)
4 to 6 GHz: 26 dB (>20:1 VSWR)
(For any two ProLink input channels, same v/div settings, typical) |
| Vertical Resolution |
8 bits; up to 11 bits with enhanced
resolution (ERES) |
| Sensitivity |
50 Ω: 2 mV–1 V/div, fully variable
(2-9.99 mV/div via zoom); 1 MΩ: 1 mV–10 V/div, fully variable |
| DC Gain Accuracy |
±1.5% of full scale |
| Offset Range |
50 Ω (ProLink):
±750 mV @ 10–118 mV/div
±4 V @ 120 mV/div -1 V/div
50 Ω (ProBus):
±750 mV @ 10–170 mV/div
±4 V @ 172 mV/div -1 V/div
1 MΩ:
±1V @ 2–128 mV/div
±10V @ 130mV-1.28V/div
& |
| Offset Accuracy |
±(1.5% of full scale + 1.0% of offset
value + 1 mV) |
| |
Horizontal System
|
| Timebases |
Internal timebase common to 4 input
channels; an external clock may be applied at the auxiliary input |
| Time/Division Range |
20 ps/div–1000 s/div (RIS mode: 20 ps/div
- 10 ns/div; Roll mode: up to 1000 s/div) |
| Clock Accuracy |
< 1 ppm + (aging of 0.5ppm/yr from
last calibration) |
| Time Interval Accuracy |
< 0.06 / SR + (clock accuracy*
Reading) (rms) |
| Jitter Noise Floor |
750 fs (TIE, typical) |
| Trigger and Interpolator Jitter |
1 psrms (typical) <0.1 ps rms
(typical, software assisted) |
| Channel-Channel Deskew Range |
±9 x time/div. setting, 100 ms max.,
each channel |
| External Timebase Reference (Input) |
10 MHz; 50 Ω impedance, applied at
the rear input |
| External Timebase Reference (Output) |
10 MHz; 50 Ω impedance, output at the
rear |
| External Clock |
30 MHz–2 GHz, 50 Ω impedance, applied
at the auxiliary input |
| |
Acquisition System
|
| Single-Shot Sample Rate/Ch |
40 GS/s on 2 Ch
20 GS/s on 4 Ch |
| Random Interleaved Sampling (RIS) |
200 GS/s for repetitive signals (20
ps/div to 10 ns/div) |
| Maximum Trigger Rate |
1,000,000 waveforms/second (in
Sequence Mode, up to 4 channels) |
| Intersegment Time |
1 µs |
| Memory Options (4 Ch / 2 Ch / 1Ch) |
S-32 Option:
32M / 64M / 64M
(15,000)
M-64 Option:
64M / 128M / 128M
(15,000)
L-128 Option:
128M / 256M / 256M
(15,000) |
| Standard Memory (4 Ch / 2 Ch / 1Ch)
(Number of Segments) |
20 M / 40 M / 40M
(5000) |
| |
Acquisition Processing
|
| Averaging |
Summed averaging to 1 million sweeps;
continuous averaging to 1 million sweeps |
| Enhanced Resolution (ERES) |
From 8.5 to 11 bits vertical
resolution |
| Envelope (Extrema) |
Envelope, floor, or roof for up to 1
million sweeps |
| Interpolation |
Linear or Sin x/x |
| |
Triggering System
|
| Modes |
Normal, Auto, Single, and Stop |
| Sources |
Any input channel, Aux, Aux/10, or
line; slope and level unique to each source (except line trigger) |
| Coupling Mode |
DC, AC, HFRej, LFRej |
| Pre-trigger Delay |
0–100% of memory size (adjustable in
1% increments of 100 ns) |
| Post-trigger Delay |
0–10,000 divisions in real time mode,
limited at slower time/div settings or in roll mode |
| Hold-off by Time |
From 2 ns up to 20 s or from 1 to
99,999,999 events |
| Internal Trigger Range |
±4.1 div from center |
| Trigger Sensitivity with Edge Trigger
(Ch 1–4) ProBus Inputs |
2 div @ < 3.5 GHz
1.5 div @ < 1.75 GHz
1.0 div @ < 200 MHz
(for DC, AC, LFRej coupling, ≥ 10 mV/div, 50 Ω ) |
| Trigger Sensitivity with Edge Trigger
(Ch 1–4) ProLink Inputs |
2 div @ < 4 GHz
1.5 div @ < 2 GHz
1.0 div @ < 200 MHz
(for DC, AC, LFRej coupling, ≥ 10 mV/div, 50 Ω ) |
| External Trigger Sensitivity, (Edge
Trigger) |
2 div @ < 1 GHz
1.5 div @ < 500 MHz
1.0 div @ < 200 MHz
(for DC, AC, LFRej coupling) |
| External Trigger Input Range |
Aux (±0.4 V); Aux/10 (±4 V) |
| Max. Trigger Frequency, SMART Trigger
|
2.0 GHz @ ≥ 10 mV/div (minimum
triggerable width 200 ps) |
| |
Basic Triggers
|
| Edge |
Triggers when signal meets slope
(positive, negative, or either) and level condition. |
| Window |
Triggers when signal exits a window
defined by adjustable thresholds |
| TV-Composite Video |
Triggers NTSC or PAL with selectable
line and field; HDTV (720p, 1080i, 1080p) with selectable frame
rate (50 or 60 Hz) and Line; or CUSTOM with selectable Fields
(1-8), Lines (up to 2000), Frame Rates (25, 30, 50, or 60 Hz),
Interlacing (1:1, 2:1, 4:1, 8 |
| |
SMART Triggers
|
| State or Edge Qualified |
Triggers on any input source only if
a defined state or edge occurred on another input source. Delay
between sources is selectable by time or events. |
| Qualified First |
In Sequence acquisition mode,
triggers repeatably on event B only if a defined pattern, state,
or edge (event A) is satisfied in the first segment of the
acquisition. Holdoff between sources is selectable by time or
events. |
| Dropout |
Triggers if signal drops out for
longer than selected time between 1 ns and 20 s. |
| Pattern |
Logic combination (AND, NAND, OR,
NOR) of 5 inputs (4 channels and external trigger input). Each
source can be high, low, or don’t care. The High and Low level can
be selected independently. Triggers at start or end of the
pattern. |
| |
SMART Triggers with Exclusion Technology
|
| Glitch |
Triggers on positive or negative
glitches with widths selectable as low as 200ps (depending on
oscilloscope bandwidth) to 20 s, or on intermittent faults. |
| Width (Signal or Pattern) |
Triggers on positive, negative, or
both widths with widths selectable as low as 200ps (depending on
oscilloscope bandwidth) to 20 s, or on intermittent faults. |
| Interval (Signal or Pattern) |
Triggers on intervals selectable
between 1 ns and 20 s. |
| Timeout (State/Edge Qualified) |
Triggers on any source if a given
state (or transition edge) has occurred on another source. Delay
between sources is 1 ns to 20 s, or 1 to 99,999,999 events. |
| Runt |
Trigger on positive or negative runts
defined by two voltage limits and two time limits. Select between
1 ns and 20 ns. |
| Slew Rate |
Trigger on edge rates. Select limits
for dV, dt, and slope. Select edge limits between 1 ns and 20 ns. |
| Exclusion Triggering |
Trigger on intermittent faults by
specifying the expected behavior and triggering when that
condition is not met |
| |
Cascade (Sequence) Triggering
|
| Capability |
Arm on "A" event, then Trigger on "B"
event. Or Arm on "A" event, then Qualify on "B" event, and Trigger
on "C" event. Or Arm on “A” event, then Qualify on “B” then “C”
event, and Trigger on “D” event |
| Types |
A, B, C, or D event: Edge, Glitch,
Width, Window, Dropout, Interval, Runt, Slew Rate, or Pattern
(analog). |
| Holdoff |
Holdoff between A and B, B and C, C
or D, or any is selectable by time or number of events |
| Reset |
Reset between A and B, B and C, C and
D, or any combination is selectable in time or number of events |
| |
High Speed Serial Protocol Triggering
|
| Data Rates |
(Option WPZi-HSPT) 100 Mb/s - 2.7,
3.0, 3.125 Gb/s |
| Pattern Length |
80 bits, NRZ or 8b10b |
| Clock and Data Outputs |
400mVp-p (typical) AC coupled |
| Clock Recovery Jitter |
1 ps rms + 0.3% Unit Interval rms for
PRBS data patterns with 50% transition density |
| Hardware Clock Recovery Loop BW |
PLL Loop BW = Fbaud/5500, 100 Mb/s to
2.488 Gb/s (typical) |
| |
Color Waveform Display
|
| Type |
Color 15.3" flat panel TFT-Active
Matrix LCD with high resolution touch screen |
| Resolution |
WXGA; 1280 x 768 pixels. |
| Number of traces |
Display a maximum of 8 traces.
Simultaneously display channel, zoom, memory and math traces. |
| Grid Styles |
Auto, Single, Dual, Quad, Octal, X-Y,
Single+X-Y, Dual+X-Y |
| Waveform Representation |
Sample dots joined, or sample dots
only |
| |
Processor/CPU
|
| Type |
Intel® CoreTM 2 Quad, 3 GHz (or
better) |
| Processor Memory |
8 GB standard |
| Operating System |
Microsoft Windows® Vista Business
Edition (64-bit) with SP1 |
| Real Time Clock |
Date and time displayed with waveform
in hardcopy files. SNTP support to synchronize to precision
internal clocks. |
| |
Setup Storage
|
| Front Panel and Instrument Status |
Store to the internal hard drive,
over the network, or to a USB-connected peripheral device. |
| |
Interface
|
| Remote Control |
Via Windows Automation, or via LeCroy
Remote Command Set |
| Network Communication Standard |
VXI-11 or VICP, LXI Class C (v 1.2)
Compliant |
| GPIB Port (optional) |
Supports IEEE – 488.2 |
| LSIB Port (optional) |
Supports PCIe Gen1 x4 protocol with
LeCroy supplied API |
| Ethernet Port |
Supports 10/100/1000BaseT Ethernet
interface (RJ45 port) |
| USB Ports |
minimum 6 total (incl. 3 front panel)
USB 2.0 ports support Windows compatible devices |
| External Monitor Port |
15 pin D-Type WXGA compatible to
support customer-supplied external monitor. DVI and power
connector to support LeCroy WPZi-EXTDISP-15 additional touch
screen display accessory. Includes support for extended desktop
operation with optional LeCroy or other |
| Peripheral Bus |
LeCroy LBUS standard |
| |
Auxiliary Output
|
| Connector Type |
BNC, located on front |
| Signal Types |
Select from calibrator, control
signals or Off |
| Output Signal |
500 Hz–5 MHz square wave or DC level;
2.5mV to 500 mV into 50 Ω (5 mV–1 V into 1 MΩ) |
| Control Signals |
Trigger enabled, trigger out,
pass/fail status, off |
| |
Power Requirements
|
| Voltage |
100–240 VAC ±10% at 45-66 Hz; 100-120
VAC ±10% at 380-420 Hz; Automatic AC Voltage Selection; |
| Max. Power Consumption |
850 W/850 VA |
| |
Environmental and Safety
|
| Temperature (Operating) |
+5 °C to +40 °C including
CD-RW/DVD-ROM drive |
| Temperature (Non-Operating) |
–20 °C to +60 °C |
| Humidity (Operating) |
5% to 80% relative humidity
(non-condensing) up to +31 °C. Upper limit derates to 50% relative
humidity (non-condensing) at +40 °C. |
| Humidity (Non-Operating) |
5% to 95% relative humidity
(non-condensing) as tested per MIL-PRF-28800F |
| Altitude (Operating) |
Up to 10,000 ft. (3048 m) at or below
+25 °C |
| Altitude (Non-Operating) |
Up to 40,000 ft. (12,192 m) |
| Random Vibration (Operating) |
0.5 grms 5 Hz to 500 Hz, 10 minutes
in each of three orthogonal axes, 30 minutes total |
| Random Vibration (Non-Operating) |
2.0 grms 5 Hz to 500 Hz, 10 minutes
in each of three orthogonal axes, 30 minutes total |
| Functional Shock |
20 g peak, half sine, 11 ms pulse, 3
shocks (positive and negative) in each of three orthogonal axes,
18 shocks total |
| |
Physical Dimensions
|
| Dimensions (HWD) |
14"H x 18.4"W x 11.4"D (355 x 467 x
289 mm) |
| Weight |
40.5 lbs. (18.4 kg) |
| Shipping Weight |
62 lbs. (28.2 kg) |
| |
Certifications
|
| Certifications |
CE Compliant, UL and cUL listed;
conforms to EN 61326-1, EN 61010-1, UL 61010-1 2nd edition, and
CSA C22.2 No. 61010-1-04 |
| |
Warranty and Service
|
| Warranty and Service |
3-year warranty; calibration
recommended annually. Optional service programs include extended
warranty, upgrades, and calibration services. |
| |
WavePro 760 Zi-A スペック
Vertical System
|
| Analog (ProLink Input) Bandwidth @ 50
Ω (-3 dB) |
6 GHz (≥10 mV/div) |
| Analog (ProBus Input) Bandwidth @ 50
Ω (-3 dB) |
3.5 GHz (≥10 mV/div) |
| Analog (ProBus Input) Bandwidth @ 1
MΩ (-3 dB) |
500 MHz (typical) (≥5 mV/div) |
| Rise Time (10–90%) |
70 ps (typical, flatness mode) |
| Rise Time (20–80%) |
53 ps (typical, flatness mode) |
| Input Channels |
4 |
| Bandwidth Limiters |
20 MHz, 200 MHz, 1 GHz, 3 GHz, 4 GHz |
| Input Impedance |
50 Ω+/-2% or 1 MΩ||16pF, 10 MΩ || 11
pF with supplied Probe |
| Input Coupling |
ProLink Inputs - 50 Ω: DC, GND
ProBus Inputs - 1 MΩ: AC, DC, GND; 50 Ω: DC, GND |
| Maximum Input Voltage |
50 Ω (ProBus): ±5 Vrms
50 Ω (ProLink): ±4 Vpeak
1 MΩ (ProBus): 250 V max. (peak AC: < 10 kHz + DC) |
| Channel-Channel Isolation |
DC to 2 GHz: 46 dB (>200:1 VSWR)
2 to 4 GHz: 34 dB (>50:1 VSWR)
4 to 6 GHz: 26 dB (>20:1 VSWR)
(For any two ProLink input channels, same v/div settings, typical) |
| Vertical Resolution |
8 bits; up to 11 bits with enhanced
resolution (ERES) |
| Sensitivity |
50 Ω: 2 mV–1 V/div, fully variable
(2-9.99 mV/div via zoom); 1 MΩ: 1 mV–10 V/div, fully variable |
| DC Gain Accuracy |
±1.5% of full scale |
| Offset Range |
50 Ω (ProLink):
±750 mV @ 10–118 mV/div
±4 V @ 120 mV/div -1 V/div
50 Ω (ProBus):
±750 mV @ 10–170 mV/div
±4 V @ 172 mV/div -1 V/div
1 MΩ:
±1V @ 2–128 mV/div
±10V @ 130mV-1.28V/div
& |
| Offset Accuracy |
±(1.5% of full scale + 1.0% of offset
value + 1 mV) |
| |
Horizontal System
|
| Timebases |
Internal timebase common to 4 input
channels; an external clock may be applied at the auxiliary input |
| Time/Division Range |
20 ps/div–1000 s/div (RIS mode: 20 ps/div
- 10 ns/div; Roll mode: up to 1000 s/div) |
| Clock Accuracy |
< 1 ppm + (aging of 0.5ppm/yr from
last calibration) |
| Time Interval Accuracy |
< 0.06 / SR + (clock accuracy*
Reading) (rms) |
| Jitter Noise Floor |
560 fs (TIE, typical) |
| Trigger and Interpolator Jitter |
1 psrms (typical) <0.1 ps rms
(typical, software assisted) |
| Channel-Channel Deskew Range |
±9 x time/div. setting, 100 ms max.,
each channel |
| External Timebase Reference (Input) |
10 MHz; 50 Ω impedance, applied at
the rear input |
| External Timebase Reference (Output) |
10 MHz; 50 Ω impedance, output at the
rear |
| External Clock |
30 MHz–2 GHz, 50 Ω impedance, applied
at the auxiliary input |
| |
Acquisition System
|
| Single-Shot Sample Rate/Ch |
40 GS/s on 2 Ch
20 GS/s on 4 Ch |
| Random Interleaved Sampling (RIS) |
200 GS/s for repetitive signals (20
ps/div to 10 ns/div) |
| Maximum Trigger Rate |
1,000,000 waveforms/second (in
Sequence Mode, up to 4 channels) |
| Intersegment Time |
1 µs |
| Memory Options (4 Ch / 2 Ch / 1Ch) |
S-32 Option:
32M / 64M / 64M
(15,000)
M-64 Option:
64M / 128M / 128M
(15,000)
L-128 Option:
128M / 256M / 256M
(15,000) |
| Standard Memory (4 Ch / 2 Ch / 1Ch)
(Number of Segments) |
20 M / 40 M / 40M
(5000) |
| |
Acquisition Processing
|
| Averaging |
Summed averaging to 1 million sweeps;
continuous averaging to 1 million sweeps |
| Enhanced Resolution (ERES) |
From 8.5 to 11 bits vertical
resolution |
| Envelope (Extrema) |
Envelope, floor, or roof for up to 1
million sweeps |
| Interpolation |
Linear or Sin x/x |
| |
Triggering System
|
| Modes |
Normal, Auto, Single, and Stop |
| Sources |
Any input channel, Aux, Aux/10, or
line; slope and level unique to each source (except line trigger) |
| Coupling Mode |
DC, AC, HFRej, LFRej |
| Pre-trigger Delay |
0–100% of memory size (adjustable in
1% increments of 100 ns) |
| Post-trigger Delay |
0–10,000 divisions in real time mode,
limited at slower time/div settings or in roll mode |
| Hold-off by Time |
From 2 ns up to 20 s or from 1 to
99,999,999 events |
| Internal Trigger Range |
±4.1 div from center |
| Trigger Sensitivity with Edge Trigger
(Ch 1–4) ProBus Inputs |
2 div @ < 3.5 GHz
1.5 div @ < 1.75 GHz
1.0 div @ < 200 MHz
(for DC, AC, LFRej coupling, ≥ 10 mV/div, 50 Ω ) |
| Trigger Sensitivity with Edge Trigger
(Ch 1–4) ProLink Inputs |
2 div @ < 6 GHz
1.5 div @ < 3 GHz
1.0 div @ < 200 MHz
(for DC, AC, LFRej coupling, ≥ 10 mV/div, 50 Ω ) |
| External Trigger Sensitivity, (Edge
Trigger) |
2 div @ < 1 GHz
1.5 div @ < 500 MHz
1.0 div @ < 200 MHz
(for DC, AC, LFRej coupling) |
| External Trigger Input Range |
Aux (±0.4 V); Aux/10 (±4 V) |
| Max. Trigger Frequency, SMART Trigger
|
2.0 GHz @ ≥ 10 mV/div (minimum
triggerable width 200 ps) |
| |
Basic Triggers
|
| Edge |
Triggers when signal meets slope
(positive, negative, or either) and level condition. |
| Window |
Triggers when signal exits a window
defined by adjustable thresholds |
| TV-Composite Video |
Triggers NTSC or PAL with selectable
line and field; HDTV (720p, 1080i, 1080p) with selectable frame
rate (50 or 60 Hz) and Line; or CUSTOM with selectable Fields
(1-8), Lines (up to 2000), Frame Rates (25, 30, 50, or 60 Hz),
Interlacing (1:1, 2:1, 4:1, 8 |
| |
SMART Triggers
|
| State or Edge Qualified |
Triggers on any input source only if
a defined state or edge occurred on another input source. Delay
between sources is selectable by time or events. |
| Qualified First |
In Sequence acquisition mode,
triggers repeatably on event B only if a defined pattern, state,
or edge (event A) is satisfied in the first segment of the
acquisition. Holdoff between sources is selectable by time or
events. |
| Dropout |
Triggers if signal drops out for
longer than selected time between 1 ns and 20 s. |
| Pattern |
Logic combination (AND, NAND, OR,
NOR) of 5 inputs (4 channels and external trigger input). Each
source can be high, low, or don’t care. The High and Low level can
be selected independently. Triggers at start or end of the
pattern. |
| |
SMART Triggers with Exclusion Technology
|
| Glitch |
Triggers on positive or negative
glitches with widths selectable as low as 200ps (depending on
oscilloscope bandwidth) to 20 s, or on intermittent faults. |
| Width (Signal or Pattern) |
Triggers on positive, negative, or
both widths with widths selectable as low as 200ps (depending on
oscilloscope bandwidth) to 20 s, or on intermittent faults. |
| Interval (Signal or Pattern) |
Triggers on intervals selectable
between 1 ns and 20 s. |
| Timeout (State/Edge Qualified) |
Triggers on any source if a given
state (or transition edge) has occurred on another source. Delay
between sources is 1 ns to 20 s, or 1 to 99,999,999 events. |
| Runt |
Trigger on positive or negative runts
defined by two voltage limits and two time limits. Select between
1 ns and 20 ns. |
| Slew Rate |
Trigger on edge rates. Select limits
for dV, dt, and slope. Select edge limits between 1 ns and 20 ns. |
| Exclusion Triggering |
Trigger on intermittent faults by
specifying the expected behavior and triggering when that
condition is not met |
| |
Cascade (Sequence) Triggering
|
| Capability |
Arm on "A" event, then Trigger on "B"
event. Or Arm on "A" event, then Qualify on "B" event, and Trigger
on "C" event. Or Arm on “A” event, then Qualify on “B” then “C”
event, and Trigger on “D” event |
| Types |
A, B, C, or D event: Edge, Glitch,
Width, Window, Dropout, Interval, Runt, Slew Rate, or Pattern
(analog). |
| Holdoff |
Holdoff between A and B, B and C, C
or D, or any is selectable by time or number of events |
| Reset |
Reset between A and B, B and C, C and
D, or any combination is selectable in time or number of events |
| |
High Speed Serial Protocol Triggering
|
| Data Rates |
(Option WPZi-HSPT) 100 Mb/s - 2.7,
3.0, 3.125 Gb/s |
| Pattern Length |
80 bits, NRZ or 8b10b |
| Clock and Data Outputs |
400mVp-p (typical) AC coupled |
| Clock Recovery Jitter |
1 ps rms + 0.3% Unit Interval rms for
PRBS data patterns with 50% transition density |
| Hardware Clock Recovery Loop BW |
PLL Loop BW = Fbaud/5500, 100 Mb/s to
2.488 Gb/s (typical) |
| |
Color Waveform Display
|
| Type |
Color 15.3" flat panel TFT-Active
Matrix LCD with high resolution touch screen |
| Resolution |
WXGA; 1280 x 768 pixels. |
| Number of traces |
Display a maximum of 8 traces.
Simultaneously display channel, zoom, memory and math traces. |
| Grid Styles |
Auto, Single, Dual, Quad, Octal, X-Y,
Single+X-Y, Dual+X-Y |
| Waveform Representation |
Sample dots joined, or sample dots
only |
| |
Processor/CPU
|
| Type |
Intel® CoreTM 2 Quad, 3 GHz (or
better) |
| Processor Memory |
8 GB standard |
| Operating System |
Microsoft Windows® Vista Business
Edition (64-bit) with SP1 |
| Real Time Clock |
Date and time displayed with waveform
in hardcopy files. SNTP support to synchronize to precision
internal clocks. |
| |
Setup Storage
|
| Front Panel and Instrument Status |
Store to the internal hard drive,
over the network, or to a USB-connected peripheral device. |
| |
Interface
|
| Remote Control |
Via Windows Automation, or via LeCroy
Remote Command Set |
| Network Communication Standard |
VXI-11 or VICP, LXI Class C (v 1.2)
Compliant |
| GPIB Port (optional) |
Supports IEEE – 488.2 |
| LSIB Port (optional) |
Supports PCIe Gen1 x4 protocol with
LeCroy supplied API |
| Ethernet Port |
Supports 10/100/1000BaseT Ethernet
interface (RJ45 port) |
| USB Ports |
minimum 6 total (incl. 3 front panel)
USB 2.0 ports support Windows compatible devices |
| External Monitor Port |
15 pin D-Type WXGA compatible to
support customer-supplied external monitor. DVI and power
connector to support LeCroy WPZi-EXTDISP-15 additional touch
screen display accessory. Includes support for extended desktop
operation with optional LeCroy or other |
| Peripheral Bus |
LeCroy LBUS standard |
| |
Auxiliary Output
|
| Connector Type |
BNC, located on front |
| Signal Types |
Select from calibrator, control
signals or Off |
| Output Signal |
500 Hz–5 MHz square wave or DC level;
2.5mV to 500 mV into 50 Ω (5 mV–1 V into 1 MΩ) |
| Control Signals |
Trigger enabled, trigger out,
pass/fail status, off |
| |
Power Requirements
|
| Voltage |
100–240 VAC ±10% at 45-66 Hz; 100-120
VAC ±10% at 380-420 Hz; Automatic AC Voltage Selection; |
| Max. Power Consumption |
850 W/850 VA |
| |
Environmental and Safety
|
| Temperature (Operating) |
+5 °C to +40 °C including
CD-RW/DVD-ROM drive |
| Temperature (Non-Operating) |
–20 °C to +60 °C |
| Humidity (Operating) |
5% to 80% relative humidity
(non-condensing) up to +31 °C. Upper limit derates to 50% relative
humidity (non-condensing) at +40 °C. |
| Humidity (Non-Operating) |
5% to 95% relative humidity
(non-condensing) as tested per MIL-PRF-28800F |
| Altitude (Operating) |
Up to 10,000 ft. (3048 m) at or below
+25 °C |
| Altitude (Non-Operating) |
Up to 40,000 ft. (12,192 m) |
| Random Vibration (Operating) |
0.5 grms 5 Hz to 500 Hz, 10 minutes
in each of three orthogonal axes, 30 minutes total |
| Random Vibration (Non-Operating) |
2.0 grms 5 Hz to 500 Hz, 10 minutes
in each of three orthogonal axes, 30 minutes total |
| Functional Shock |
20 g peak, half sine, 11 ms pulse, 3
shocks (positive and negative) in each of three orthogonal axes,
18 shocks total |
| |
Physical Dimensions
|
| Dimensions (HWD) |
14"H x 18.4"W x 11.4"D (355 x 467 x
289 mm) |
| Weight |
40.5 lbs. (18.4 kg) |
| Shipping Weight |
62 lbs. (28.2 kg) |
| |
Certifications
|
| Certifications |
CE Compliant, UL and cUL listed;
conforms to EN 61326-1, EN 61010-1, UL 61010-1 2nd edition, and
CSA C22.2 No. 61010-1-04 |
| |
Warranty and Service
|
| Warranty and Service |
3-year warranty; calibration
recommended annually. Optional service programs include extended
warranty, upgrades, and calibration services. |
| |
WavePro 7Ziシリーズ スペック詳細 （PDF:700K）
Sampling Rate Options
|
WPZi-1.5GHz-4X20GS
20 GS/s (40 GS/s Interleaved) Sampling Rate
Option for 1.5 GHz WavePro Zi |
High Speed Output Accessories
|
LSIB-1
High speed PCIe Gen1 x4 digitizer output for
LeCroy oscilloscope. Half-height card with
custom connector |
LSIB-HOSTBOARD
PCI Express x4 Host Interface Board for
desktop PC |
LSIB-HOSTCARD
PCI Express x1 Express Card Host Interface
for laptop Express Card slot |
LSIB-CABLE-3M
PCI Express x 4 3-meter cable with x4 cable
connectors included |
LSIB-CABLE-7M
PCI Express x 4 7-meter cable with x4 cable
connectors include |
Serial Data Analysis
|
WPZi-CBL-DE-EMBED
Remove cable effects from your measurements
|
WPZi-SDAII
SDA II Serial Data Analysis Option |
WPZi-EYEDRII
Eye Doctor II Advanced Signal Integrity
Tools for WavePro 7 Zi Oscilloscopes, SDA 7
Zi Serial Data Analyzers, and DDA 7 Zi Disk
Drive Analyzers |
Serial Data Compliance
|
QPHY-MIPI-DPHY
QualiPHY Enabled MIPI D-PHY Software Option
|
QPHY-DDR2
QualiPHY DDR2 Compliance Software Option
|
QPHY-DDR3
QualiPHY Enabled DDR3 Software Option |
QPHY-ENET
QualiPHY Ethernet Application Software |
QPHY-HDMI
QualiPHY Enabled HDMI Software Option
(TF-HDMI-3.3V-QUADPAK required;WavePro 760Zi
requires SDA II option) |
QPHY-LPDDR2
QualiPHY LPDDR2 Compliance SW |
QPHY-PCIe
QualiPHY Enabled PCIe Software Option (for
Gen1 and Gen2 testing) |
QPHY-SATA-TSG-RSG
QualiPHY Enabled SATA Software Option |
QPHY-USB
USB Application Software Package |
QPHY-UWB
WiMedia UWB Transmitter Measurement Software
Option |
ENET-2ADA-BNCSMA
2 x BNC to SMA Adapter |
ENET-2CAB-SMA018
2 x 18 inch SMA to SMA Cable |
ENET-2CAB-SMA036
2 x 36 inch SMA to SMA Cable |
WPZi-SDM
Serial Data Mask Software Package for
WavePro Zi Series |
Computer Upgrade
|
WPZi-2-UPG-8GBRAM
Upgrade from 2 GB to 8 GB CPU RAM |
WPZi-4-UPG-8GBRAM
Upgrade from 4 GB to 8 GB CPU RAM |
GPIB-2
GPIB Option for LeCroy oscilloscope.
Half-height card with custom connector. |
WPZi-500GB-HD
Upgrade from standard size hard drive to 500
GB hard drive |
WPZi-160GB-RHD-02
Additional 160 GB Hard Drive for WPZi.
Includes Windows Vista OS, LeCroy
oscilloscope software and critical scope
operational file duplicates. |
WPZi-500GB-RHD-02
Additional 500 GB Hard Drive for WPZi.
Includes Windows Vista OS, LeCroy
oscilloscope software and critical scope
operational file duplicates. |
Serial Trigger and Decode
|
WPZi-SATAbus D
SATA Decode annotation option for WavePro
7Zi Series Supports SATA Gen 1, 2, and 3
|
WPZi-1553 TD
MIL-STD-1553 Trigger and decode option for
WavePro Zi |
WPZi-8B10B D
8b10b Decode Option for WavePro Zi Series
Oscilloscopes |
WPZi-ARINC429bus DSymbolic
ARINC 429 Bus Symbolic Decode option for
WavePro Zi |
WPZi-AudioBus TD
AudioBus Trigger and decode Option for
WavePro 7Zi |
WPZi-AudioBus TDG
AudioBus Trigger, decode, and Graph Option
for WavePro 7Zi |
WPZi-CANbus TD
CAN Bus Trigger & Decode Option for WavePro
Zi Series Oscilloscopes |
WPZi-CANbus TDM
CAN Bus Trigger, Decode, and Measure Option
for WavePro Zi Series Oscilloscopes |
WPZi-DigRF3Gbus D
DigRF 3G Bus Decode option for WavePro Zi
|
WPZi-DPHYbus D
D-PHY Bus Decode option for WavePro Zi |
WPZi-FlexrayBus TD
FlexRay Bus Trigger & Decode Option for
WavePro Zi Series Oscilloscopes |
WPZi-FlexRayBus TDP
FlexRay Bus Trigger, Decode, and Physical
Layer Test Option for WavePro Zi Series
Oscilloscopes |
WPZi-HSPT
50 Mb/s to 3.125 Gb/s High Speed Serial
Trigger Option for 4-6 GHz Oscilloscopes &
Disk Drive Analyzers |
WPZi-I2Cbus TD
I2C Bus Trigger & Decode Option for WavePro
Zi Series Oscilloscopes |
WPZi-LINbus TD
LIN Bus Trigger & Decode Option for WavePro
Zi Series Oscilloscopes |
WPZi-MSPT
50 Mb/s to 1.25 Gb/s Medium Speed Serial
Trigger Option for 2.5-3.5 GHz Oscilloscopes
& Disk Drive Analyzers |
WPZi-PCIEbus D
PCI Express (Gen 1.x, 2.0, and 3.0) Protocol
Link Layer Decode Annotation for WavePro 7
Zi Series Oscilloscopes and Analyzers |
WPZi-PROTObus MAG
Serial Debug Toolkit - Measure Analyze Graph
for WavePro Zi |
WPZi-ProtoSync
Decode Annotation and Protocol Analyzer
Software Synchronization Option for WavePro
7Zi/Zi-A |
WPZi-ProtoSync-BT
Decode Annotation and Protocol Analyzer +
Bit Tracer Software Synchronization Option
for WavePro Zi/Zi-A |
WPZi-SPIbus TD
SPI Bus Trigger & Decode Option for WavePro
Zi Series Oscilloscopes |
WPZi-UART-RS232bus TD
UART and RS232 Bus Trigger & Decode Option
for WavePro Zi Series Oscilloscopes |
WPZi-USB2bus D
USB 2.0 Bus Decode option for WavePro Zi
|
WPZi-USB3bus D
USB 3.0 Decode option for WavePro Zi |
Jitter Analysis Software
|
WPZi-JTA2
Jitter Timing and Analysis Software Package
for WavePro Zi Series |
WPZi-JITKIT
Clock, clock-data Jitter Analysis and views
of time, statistical, spectral, and jitter
overlay |
Synchronize Oscilloscope Options
|
Zi-8CH-SYNCH
HW Kit to allow combination of channels from
two 8Zi oscilloscopes |
Miscellaneous
|
KYBD-1
Keyboard |
WPZi-HARDCASE
Hard carrying case for all WavePro Zi Series
oscilloscopes |
WPZi-SOFTCASE
Soft carrying case for all WavePro Zi Series
oscilloscopes |
RACKMOUNT-1
Rack-mount accessory for converting a
WavePro Zi series oscilloscope to an 8U
rack-mounted package |
ZI-EXTDISP-15
Top-mounted, Fully Integrated 15.3" WXGA
with Touch Screen Display, Including all
Cabling and Software |
TTL-AUX-OUT
Accessory for Zi oscilloscopes to enable TTL
level output from the Aux Out connector |
Zi-FrontPanel
Removable front panel for WavePro 7Zi and
WaveMaster 8Zi Oscilloscopes |
Zi-FrontPanel-4Ch
Removable front panel with 4 independent
channel controls for WavePro 7Zi and
WaveMaster 8Zi Oscilloscopes |
Rise-Time-Filter-100ps
Low-Pass Rise Time Filter 100 ps |
Rise-Time-Filter-150ps
Low-Pass Rise Time Filter 150 ps |
20dB-SMA-Attenuator
20 dB Attenuator |
Other Software Options
|
WPZi-XDEV
Developer's Tool Kit Option for WavePro Zi
Series |
WPZi-SPECTRUM
Spectrum Analyzer and Advanced FFT Option
for WavePro Zi Series |
WPZi-EMC
EMC Pulse Parameter Software Package for
WavePro Zi Series |
WPZi-ET-PMT
Electrical Telecom Pulse Mask Test Package
for WavePro Zi Series |
Data Storage Software
|
WPZi-AORM
Advanced Optical Recording Measurement
Package for WavePro Zi Series |
WPZi-DDM2
Disk Drive Measurements Software Package for
WavePro Zi Series |
Power Analysis Software
|
WPZi-PMA2
Power Measure Analysis Software Package |
Digital Filtering Software
|
WPZi-DFP2
Digital Filter Software Package for WavePro
Zi Series |
Mixed Signal Solutions
|
MS-500
500 MHz Maximum Input Frequency, 18
Channels, 50 Mpts/ch Mixed Signal
Oscilloscope Option |
MS-500-36
250 MHz Maximum Input Frequency, 36
Channels, 25 Mpts/ch Mixed Signal
Oscilloscope Option |
MS-250
250 MHz Maximum Input Frequency, 18
Channels, 10 Mpts/ch Mixed Signal
Oscilloscope Option |
Mixed Signal Accessories
|
PK400-1
Large gripper probe set for 0.10'' (2.54 mm)
pin pitch, includes 10 probes with
color-coded leads |
PK400-2
Medium gripper probe set for 0.04'' (1.0 mm)
pin pitch, includes 10 probes with
color-coded leads |
PK400-3
Small gripper probe set for 0.008'' (0.2 mm)
pin pitch, includes 10 probes with
color-coded leads |
MSO-MICTOR
Mictor Cable, D0-D35 |
MSO-3M
3M Interconnect Cable, D0-D17 or D18-D35
|
Serial Data Test Fixtures
|
TF-DSQ
Probe Deskew and Calibration Fixture |
TF-ENET-B
10/100/1000Base-T Compliance Test Fixture
|
TF-ET
Telecom Adaptor Kit 100Ω, 120Ω, 75Ω |
TF-HDMI-3.3V-QUADPAK
HDMI Pull-Up Terminator Quad Pack – for Use
with the Efficere ET-HDMI-TPS-S Test Fixture
|
TF-SATA-C
SATA Compliance Test Fixture (*WavePro 7 Zi
and WaveMaster 8 Zi class oscilloscopes
require the SDA II software option; **20M
memory required) |
TF-SATA-C-Kit
SATA Compliance Test Kit (*WavePro 7 Zi and
WaveMaster 8 Zi class oscilloscopes require
the SDA II software option; **20M memory
required) |
TF-USB-B
USB 2.0 Testing Compliance Test Fixture |
Current Probes
|
CP030
30 Amps, 50 MHz BW Current Probe - AC/DC , 50 Amp Peak Pulse |
CP031
30 Amps, 100 MHz BW Current Probe - AC/DC , 50 Amp Peak Pulse |
AP015
30 Amps, 50MHz BW Current Probe - AC/DC, 50 Amp Peak Pulse |
CP150
150 Amps, 10 MHz BW Current Probe - AC/DC , 500 Amp Peak Pulse |
CP500
500 Amps, 2 MHz BW Current Probe - AC/DC , 700 Amp Peak |
DCS015
Deskew Calibration Source for AP015 |
Differential Amplifiers
|
DA1855A
DA1855A, 100 MHz Differential Amplifier with fast over drive
recovery, calibrated offset, and selectable LP filters |
DXC100A
DXC100A, Selectable ÷100 or ÷10 , Passive Differential Probe Pair
for DA18xxA series |
DXC200
÷1,50 MHz low capacitance Passive Differential Probe Pair for
DA18xxA series |
DXC-5100
÷100 2.5KV Passive High Voltage Probe Pair for DA18xxA series.
Requires DA101 for full performance |
DA101
÷10 1MOhm Passive Attenuator for DXC series probes |
DA1855A-PR2
2 Ch, 100 MHz Differential Amplifier with fast over drive recovery,
calibrated offset, and selectable LP filters |
DA1855A-PR2-RM
Rack mountable version of the DA1855A-PR2 |
DA1855A-RM
DA1855A with rackmount |
Differential Probes
|
WL-PLink
WaveLink ProLink probe body >3.5 GHz |
WL-Pbus
WaveLink ProBus probe body = 3.5 GHz |
D600A-AT
WaveLink 7.5 GHz Differential Probe with Adjustable Tip Module |
D300A-AT
WaveLink 4 GHz Differential Probe with Adjustable Tip Module |
D620
WaveLink 6 GHz Differential probe module 5V |
D610
WaveLink 6 GHz Differential probe module 2.5V |
D420
WaveLink D320 3.5 GHz/5Vp-p and +/-3V Offset Range Differential
Amplifier Small tip Module |
D410
WaveLink D410 4 GHz/2.5Vp-p and +/-3V Offset Range Differential
Amplifier Small tip Module |
D320
WaveLink 3.5 GHz Differential probe module 5V |
D310
WaveLink 3.5 GHz Differential probe module 2.5V |
D620-PT
WaveLink D620 6 GHz/5Vp-p and +/-3V Offset Range Differential
Amplifier Small Tip Module with Dx20-PT Adjustable Positioner Tip.
4.8 mVrms (typical) probe + scope noise. Includes XYZ Positioner
Assembly with Mechanical Interconnects, Adhesive Kit, Connection
Guides, Hand-held Wand, and Replacement Pins (Qty. 4)/Sockets(Qty.
2). |
D610-PT
WaveLink D610 6 GHz/2.5Vp-p and +/-3V Offset Range Differential
Amplifier Small Tip Module with Dx10-PT Adjustable Positioner Tip.
2.8 mVrms (typical) probe + scope noise. Includes XYZ Positioner
Assembly with Mechanical Interconnects, Adhesive Kit, Connection
Guides, Hand-held Wand, and Replacement Pins (Qty. 4)/Sockets(Qty.
2). |
D500PT
WaveLink 6 GHz Differential Positioner Mounted Tip Module |
D420-PT
WaveLink D420 4 GHz/5Vp-p & +/-3V Offset Range Differential
Amplifier Small Tip Module w/Dx20-PT |
D410-PT
WaveLink D410 4 GHz/2.5Vp-p & +/-3V Offset Range Differential
Amplifier Small Tip Module w/Dx10-PT |
D320-PT
WaveLink D320 3.5 GHz/5Vp-p and +/-3V Offset Range Differential
Amplifier Small Tip Module with Dx20-PT Adjustable Positioner Tip.
4.8 mVrms (typical) probe + scope noise. Includes XYZ Positioner
Assembly with Mechanical Interconnects, Adhesive Kit, Connection
Guides, Hand-held Wand, and Replacement Pins (Qty. 4)/Sockets(Qty.
2). |
D310-PT
WaveLink D310 3.5 GHz/2.5Vp-p and +/-3V Offset Range Differential
Amplifier Small Tip Module with Dx10-PT Adjustable Positioner Tip.
2.8 mVrms (typical) probe + scope noise. Includes XYZ Positioner
Assembly with Mechanical Interconnects, Adhesive Kit, Connection
Guides, Hand-held Wand, and Replacement Pins (Qty. 4)/Sockets(Qty.
2). |
D600ST
WaveLink 7 GHz Differential Probe with Small Tip Module (includes
D6000ST-SI, D600ST-QC, D600ST-SP) |
D350ST
WaveLink 4 GHz, 5 V Differential with Small Tip Module |
ZD1500
1.5 GHz, 1.0 pF Active Differential probe |
ZD1000
1 GHz, 1.0 pF Active Differential probe |
ZD500
500 MHz, 1.0 pF Active Differential probe |
Dx20-PT-KIT
WaveLink Dx20-PT Adjustable Positioner Tip Kit. Includes XYZ
Positioner Assembly with Mechanical Interconnects, Adhesive Kit,
Connection Guides, Hand-held Wand, and Replacement Pins (Qty. 4)/Sockets(Qty.
2). |
Dx10-PT-KIT
WaveLink Dx10-PT Adjustable Positioner Tip Kit. Includes XYZ
Positioner Assembly with Mechanical Interconnects, Adhesive Kit,
Connection Guides, Hand-held Wand, and Replacement Pins(Qty. 4)/Sockets(Qty
2). |
AP034
1 GHz Active Differential Probe |
AP033
500 MHz Active Differential Probe |
High Voltage Probes
|
PPE1.2KV
10:1/100:1 200/300 MHz 5M Ohm/50M Ohm |
PPE2KV
100:1 400 MHz 50M Ohm High Voltage Probe |
PPE4KV
100:1 400 MHz 50M Ohm High-Voltage Probe |
PPE5KV
100:1 400 MHz 50M Ohm High-Voltage Probe |
PPE6KV
1000:1 400 MHz 50M Ohm High-Voltage Probe |
PPE20KV
1000:1 100 MHz 100M Ohm High-Voltage Probe |
High Voltage Differential Probes
|
AP031
15 MHz Differential Probe |
ADP300
High-Voltage Active Differential Probe |
ADP305
High-Voltage Differential Probes From LeCroy |
Optical Probes
|
OE425
Short wavelength O/E Converter (500-870 nm) |
OE455
Long wavelength O/E Converter (950-1630 nm) |
OE525
Short wavelength O/E Converter (500-870 nm) |
OE555
Long wavelength O/E converter |
Probe Parts and Kits
|
PACC-ZD001
Y Lead adapter, qty 1 |
PACC-ZD002
Solder in lead, qty 2 |
PACC-ZD003
Long spring ground, qty 2 |
PACC-ZD004
Tip Saver, qty 2 |
PACC-ZD005
Swivel tip adapter |
PACC-ZD006
Small IC adapter, qty 2 |
PACC-ZD007
Micro pogo pin tip, qty 6 |
LPA-SMA-KIT-A
Kit of Pro-Link to SMA Adapter, new style |
LPA-SMA-A
Pro-Link to SMA Adapter, new style |
Dxx0-Cable-HiTemp
Replacement 30" matched cable set for use with HiTemp Solder tip
leadset |
Dx20-SP
Replacement Square Pin lead set for D320/D620 |
Dx20-SI
Replacement Solder tip lead set for D320/D620 |
Dx20-SI-HiTEMP
Replacement Solder tip leadset for use with D620/D320 and
temperature extension cables |
Dx20-QC
Replacement Quick Connect lead set for D320/D620 |
Dx20-PT
Replacement Dx20-PT Tip with Qty. 4 Pogo Pin Tips and Qty. 2 Sockets
|
Dx20-HiTEMP
WaveLink Temperature extension cables for Dx20. Includes 1 set of
matched 30" high temp cables, 1 solder tip leadset. |
Dx10-SP
Replacement Square Pin lead set for D310/D610 |
Dx10-SI
Replacement Solder tip lead set for D310/D610 |
Dx10-SI-HiTEMP
Replacement Solder tip leadset for use with D610/D310 and
temperature extension cables |
Dx10-QC
Replacement Quick Connect lead set for D310/D610 |
Dx10-PT
Replacement Dx10-PT Tip with Qty. 4 Pogo Pin Tips and Qty. 2 Sockets
|
Transmission Line Probes
|
PP066
7.5 GHz Low Capacitance ÷10/÷20 probe |
|
|
|
